Bloor and Pillar Closing Down Auction

Mori Seiki CNC Lathe

Skylarc Ref P161365

Model: Mori Seiki NL2500Y/700 CNC Lathe
Three phase
Swing over bed 923mm
Swing over cross slide 755mm
Max turning diameter 356mm
Max turning length 705mm
X axis travel 260mm
Y axis travel +50mm -50mm
Z axis travel 795mm
Max spindle speed 4000rpm
80mm spindle bore diameter
12 tool turret
Tailstock travel 734mm
18.5kW main spindle motor
Live tool holders
5 vertical and 4 horizontal
Morse taper No.5 tailstock
End grooving holder
5 external tool holders
4 internal tool holders
Bartec Rapidfeed 896 barfeed (faulty)
Won't feed past the first bar and gives an error
250mm three jaw chuck
Huge range of jaws (approx 80 sets)
Manuals
Some transport brackets
Accessories
Manufactured 2006
9369 total hours
7959 cutting hours
Very tidy machine ready for work

You will need your own lifting equipment for loading this machine

Haas VF2SS Vertical Machining Center

Skylarc Ref T160537

Model: Haas VF-2SS Vertical Machining Centre
Manufactured 2007
Three phase
Haas controller
Table dimensions 910mm x 355mm
Table travels
X 761mm
Y 412mm
Z 502mm
Spindle to table max: 610mm min: 102mm
22kw main spindle motor
Max weight on table 680kg
24 tool carousel
High speed tool changer
BT40 spindle taper
12000rpm max spindle speed
Through spindle coolant
Exact-Machinery NOT-250R 4th axis
Tidy machine ready to go
Exact digital control
Approx 4000kg
You will need to organise your own lifting and decommissioning for this machine

20' Water Tank Shipping Container

Skylarc Ref C161274

20' Water Tank Shipping Container.
Approx 25,000 litres
Pumps not included

Large Industrial Shot Blasting Machine

Skylarc Ref U160954

Large Industrial Shot Blasting Machine.
Manufactured 09/2006 by Abrastive Blasting Service & Supplies, Australia.
Model No. A930330.52
Interior room approx 1650x1700x1450mm.
Rotating inner table approx 1550mm diameter.
3-phase.
Run hour clock reads 1665 hours.
Some molds for making parts
Note that electrical power will be decommissioned prior to buyer pickup but buyer will need to remove top vertical portion of main unit as well.as dissssemble the exterior hopper with tall vent chimney. The chimney will require a Crane to remove.

2007 Toyota Hilux

Skylarc Ref H161331

2007 Toyota Hilux
Single cab
2.7 petrol engine
Misses at idle
5 speed manual transmission
Two wheel drive
2570mm x 1800mm drop side aluminum deck
Lapsed registration
Yellow engine light stays on
Starts runs and drives ok
Failed WOF on rust in the chassis
Hail damage type dents on bonnet

Large Mezzanine Floor Pallet Racking System

Skylarc Ref Z161479

Capital style pallet racking mezzanine floor
16 metres long x 15.5 metres wide x 5.4 metres tall
Consists of a lower shelving area with 4 rows of shelving 2 bays long with multiple levels
Upper level with stand alone shelving units
Plastic grid and MDF sheet flooring
Wooden stairs to
Buyer will need to dismantle in early February in with coordination the landlord for access

Haas VF3 Project Vertical Machining Center

Skylarc Ref C160546

Haas VF3 vertical machining center
Manufactured 1997
1400mm x 500mm table
20 station BT40 tool carousel
X Axis Travel: 1016 mm
Y Axis Travel: 508 mm
Z Axis Travel: 635 mm
Max Table Load: 1587 kg
Spindle Motor: 11.2 kW
Spindle Speed: 8,100 rpm
Haas controller
Coolant pump
Machine powers up but has an unknown fault, suspect X axis servo
Machine weighs approx 6 ton, buyer will need to decommission for collection get

Heidenreich & Harbeck Lathe

Skylarc Ref B160571

Model: Heidenreich & Harbeck VDF 18 RD
Total bed length 1900
Distance between centers approx 1200mm
Swing over bed 400mm
11 spindle speeds
56 - 1600 rpm
54mm spindle bore
Metric and imperial thread cutting
Taper cutter
Morse taper No.4 tail stock
250mm independent four jaw chuck
Fixed steady
Some accessories
On 32amp three phase plug
Reverse currently not working

Kanga Diesel Hydraulic Loader

Skylarc Ref Z161375

Kanga 420 stand on loader
Three way bucket
Three cylinder diesel engine
4 wheel hydraulic drive
Starts and runs well but needs a 12v battery
Hydraulic leak on one bucket line

Miyano CNC Lathe with Bar Feeder

Skylarc Ref A161246

Miyano BND-42T5 CNC Lathe
Turning length 190 mm
Turning diameter 42 mm
Fanuc 18-T CNC controller
Faulty screen but runs on external screen
Two jaw chuck 135mm diameter
Collet chuck (two sleeves for different sizes)
Spindle taper A2-6
Spindle bore 50.8 mm
12 position main turret
6 position B turret
Live tooling
Max spindle speed 5000 rpm
Spindle motor power 7.45 kW
Bartec bar feeder takes 5 metre lengths
Parts catcher with exit conveyer
Wide range of collets, sleeves, tool holders
Some chuck jaws
Super reliable production machine been running all day every day for the last 20 years
Buyer will be responsible for decommissioning it

20' Shipping Container

Skylarc Ref T161291

20' Shipping Container.
Contents NOT included.
Condition - Container is in average cosmetic condition, no obvious structural damage, no holes in walls or floors, doors close and seal correctly. Container does have a lot of surface rust.

20' Shipping Container

Skylarc Ref D161275

20' Shipping Container.
Contents NOT included.
Condition - Container is in below average condition quite a bit of rust in walls, doors and Cieling. doors close and seal correctly. Container does have a lot of rust.
Has holes in walls for power and gas lines. Container contains a switch board and 2 light fixtures

20' Container and Contents

Skylarc Ref W161476

20' Shipping Container
Quite Rusty with small holes in roof and walls/floor
Closes and seals fine.
Contents include Some electronic boards, an old welding generator (Unkonwn Condition), Locker set, welding Cables and storage racks, the Contents on top of the container are included.

20' Cintainer and Contents

Skylarc Ref V161475

20' Shipping Container
Quite Rusty with small holes in roof
Closes and seals fine.
Contents on top of the container are included. These items appear to be half of a compartment and some drums.

20' Container

Skylarc Ref S161472

20' Shipping Container
Okay Condition, Front left door is VERY rusty , No visible signs of holes on interior.
Contents Not Included.

Fine Limit Granite Engineering Table, 1825x1220mm

Skylarc Ref F160783

Fine Limit Granite Engineering Table.
Manufactured by W.B.J. Granite LTD, England.
178mm thick granite top.
Heavy Steel detached support frame.
NOTE buyer will need to contact us before pickup as some preparation, and deconstruction of a wall the item is in, will need to be done to remove from its room.

Honden Single Phase Lathe

Skylarc Ref Q160872

Model: Honden LC-850BM
Bed length 1200mm
Distance between centers approx 800mm
Swing over bed approx 340mm
Swing over gap approx 480mm
Swing over cross slide approx 200mm
Three phase 1 1/2hp main motor
12 spindle speeds
60rpm - 1240rpm
Metric and imperial thread cutting
2 tool parts
160mm three jaw chuck (2 jaw sets)
32mm spindle bore
No.3 MT tailstock
Assorted drill chucks
Small 4 jaw (may not fit this lathe)
Assorted centers
Some tooling
Manufactured 1982

Tesa Micro-hite 3D Coordinate Measuring System, Faulty Screen

Skylarc Ref W160800

Tesa Micro-hite 3D Coordinate Measuring System.
Made in Switzerland, age unknown.
Includes Renshaw branded attachments, see photos
Includes manuals.
Includes steel drawer table 865x865x740mm.
NOTE that the control screen is Faulty, see photos. Vendor is including an email printout with details of replacement costs (£395) and source. Screen will need replacing before machine can be operated.

AB Arboga Maskiner Drill Mil

Skylarc Ref D159949

Model: AB Arboga Maskiner U2508 Gear Head Milling and Drilling Machine
3 phase 0.75kw motor
4 gear ranges giving 8 spindle speeds
100, 205, 345, 695, 440, 885, 1450, 2900 rpm
250mm x 560mm T slot table
Approx 110mm spindle travel
Adjustable head
MT.3 spindle taper
Fitted with 16mm chuck
20 amp plug
Top quality Swedish machine

Pehaks Automatic Metal Bandsaw

Skylarc Ref A159894

Model: Pehaka ROB-200S Bandsaw
Three phase
Max cutting width approx 350mm
Auto feed
2480mm x 465mm feed rollers

Metal Cutoff Bench with Three Saws

Skylarc Ref A160882

Long length metal cutoff bench
Three Saws
Brobo cold cut saw
2 x high speed cutoff saws (one incomplete)

Arboga Maskiner Drill Mill

Skylarc Ref A160596

Model: Rhema Maschinenbau EM 825 Gear Head Milling and Drilling Machine
3 phase 0.6kW motor
4 gear ranges giving 8 spindle speeds
100, 150, 205, 300, 440, 640, 880, 1280 rpm
250mm x 565mm T slot table
Approx 110mm spindle travel
Adjustable height head
MT.3 spindle taper
Fitted with milling vice
Slitting blade
Mounted on pallet

Arboga Maskiner Drill Mill

Skylarc Ref Z160595

Model: Arboga Maskiner EM 825 Gear Head Milling and Drilling Machine
3 phase 0.6kW motor
4 gear ranges giving 8 spindle speeds
100, 150, 205, 300, 440, 640, 880, 1280 rpm
250mm x 565mm T slot table
Approx 110mm spindle travel
Adjustable height head
MT.3 spindle taper
Mounted on pallet

Microweily CNC Lathe

Skylarc Ref D160547

Model: Microweily TY-26TR CNC (TY-2660TRCN)
Manufactured 2001
Swing over bed 660mm
Swing over cross slide 380mm
Center height 330mm
460mm bed width
3000mm bed length
105mm spindle bore
20hp main spindle motor
Z axis travel 1500mm
X axis travel 500mm
400mm four jaw chuck
300mm three jaw chuck
Fagor 8055T CNC controller
Morse taper No.5 tailstock
Fixed steady
Three phase
Some manuals
Machine powers up but won't run
Believed to have a faulty PLC
Buyer will need to decommission this machine freet

Okuma CNC Lathe

Skylarc Ref S160536

Okuma LC20 CNC Lathe
Swing Over Bed: 400 mm
Maximum Turning Diameter: 300 mm
Maximum Work Length: 250 mm
X Axis Travel (Upper Turret): 160 mm
X Axis Travel (Lower Turret): 110 mm
Z Axis Travel (Upper/Lower): 520 mm
Rapid Traverse Rate (X Axes): 5.08 m/min
Spindle Bore: 56 mm
Maximum Bar Capacity: 45 mm
Spindle Speeds: 65 - 3500 RPM
Spindle Motor: 22.4 kW
Turret Capacity (Upper/Lower): 8/8 station turret
250mm 3 jaw chuck
300mm 3 jaw chuck
Okuma CNC controller
Manuals

WES Sand Reclamation Plant

Skylarc Ref F160965

Capacity of approx 2.5 tons per hour
Storage hopper
Attridder mixes and crushes sand
Fluid bed cooler classifier
Reverse pulse dust collector
Approx 6-metres max height.
Includew Instalation and operation manual.
NOTE - This unit is unassembled in various parts within the factory. Buyer will have to figure out how reassemble the components themselves.

Steel Rack and Contents

Skylarc Ref F161485

2930mm x 1150mm x 2050mm steel rack
Contents includes
2 lengths 77mm x 3800mm stainless pipe (one bent)
5 lengths 25mm x 4900mm aluminum pipe
40mm x 20mm aluminum bar (approx 4900mm)
Assorted small diameter stainless pipe
15 x 12mm aluminum rod (approx 4900mm)
65mm x 65mm x 3400mm approx aluminum bar
7 x 25mm x 3mm x 3400mm long brass
185mm diameter x 790mm long stainless bar
2 lengths 55mm diameter stainless bar 2300mm, 3100mm
5mm stainless rod

Arboga Maskiner Drill Mill

Skylarc Ref E159924

Model: AB Arboga Maskiner EM 825 Gear Head Milling and Drilling Machine
3 phase 0.9hp motor
4 gear ranges giving 8 spindle speeds
100, 250, 440, 1040, 205, 510, 885, 2080 rpm
250mm x 565mm T slot table
Approx 110mm spindle travel
Adjustable height head
MT.3 spindle taper
Fitted with 13mm chuck
Modified with 2 x desouter automatic drills
Steel plate and pneumatic systems

Cairo Punch and Shear

Skylarc Ref F159899

Cairo flywheel iron worker
Model MF-16
Three phase
Punch, shear, notching
32 amp plug

Herbert 5 Head Gang Drill

Skylarc Ref C159896

Rotary station with 6 heads
8 speeds 74 - 2850rpm
All with chucks
4 x vertical drills
Each with 8 speeds 74-2850rpm
No.3 Morse Taper
All gear head drills
Rise and fall T Slot table
1850mm x 500mm T Slot table
Automatic feeds
3 phase 9hp motors
Coolant pump
Record vice

Jones and Shipman Tool Cutter Grinder

Skylarc Ref J160579

Jones and Shipman Model 310 (60342)
8" x 16" tool cutter grinder
Positive indexing attachment
Various tailstocks
Range of wheels
Manuals

Jones and Shipman Tool Cutter Grinder

Skylarc Ref I160578

Jones and Shipman Model 310
8" x 16" tool cutter grinder
Internal grinding attachment
Various tailstocks
Range of wheels
Manuals
Driving dogs
Broken wheel on be end

Mazak Vertical Machining Center

Skylarc Ref A160544

Model: Mazak Impulse 30
Manufactured 2001
X axis travel 430mm
Y axis travel 300mm
Z axis travel 250mm
BT30 spindle taper
10000rpm spindle speed
10 tool carousel
Mazatroll CNC controller
Pallet changer
5.9kW main spindle motor
Machine powers up but has unknown faults
Suspect it's lost it's parameters
Some software and manuals
Parts or project

This machine is located behind other machines and collection will be in the second pickup week

Vintage Sintokogio Metal Shot Preening Anodizer Machine STB-1B

Skylarc Ref B160961

Vintage Sintokogio Metal Shot Preening Anodizer Machine.
Model No.STB-1B.
Manufactured in Japan, July 1966.
3-phase
Interior dimensions approx 780mm diameter and approx 740mm deep.
Owner states that the unit is operational.

Foundry Induction Furnaces and Control Systems

Skylarc Ref K161386

Inductotherm hydraulic tilting furnaces
Tilt control panel
Inductotherm 205kVa electric control panel
Inductotherm popup furnace with lifting mechanism
Made in Australia
Units will be electrically disconnected but buyer will need to decommission everything else

Cincinnati Traveling Column Milling Machine

Skylarc Ref K161334

Cincinnati horizontal/vertical milling machine
NT50 spindle tapers
1380mm x 300mm T Slot table
Spindle speeds 50-765rpm
Rapid traverse Power feeds
Has been used for a specialist job so has some modification
Includes vertical head

Portable Office Building

Skylarc Ref B161273

Portable Office Building
Has 2 windows and 1 door. Floor has 2 Holes in it (See Photos)
Quite a few dents and scratches and one of the corners has had the edge ripped open (See Photos)
Contents included.

Small McGregor Furnace

Skylarc Ref G159900

Model: McGregor H.T.4
Max temperature 1200c
Internal dimensions 300mm x 280mm x 510mm deep
Control panel
Will be unwired for collection

Heavy Duty Steel Workshop Shelving

Skylarc Ref G160706

Heavy Duty Steel Workshop Shelving / Workbench
- Heavy Steel shelf/Workbench unit 2880mm long, 630mm wide 2280mm tall. Workbench height 1165mm. Upper shelf section 305mm wide. Frame is welded 75x40mm channel steel.
Wooden Cabinet not included

Condition- Steel workbench/shelf is one complete welded unit and does NOT dissasemble! Very solid unit.
Note - Other Items seen on, within, and near above two units are NOT included!

Buyer needs to bring appropriate vehicle/Trailer for removing these large items.

Diesel Fired Foundry Furnace by Morgan Major

Skylarc Ref Y160958

Diesel Fired Foundry Furnace by Morgan Major.
Model number and age unknown.
Single Phase.
Crucible interior approx 400mm diameter, 550mm deep.
Operational condition is unknown.

Tanner Single Phase Bandsaw

Skylarc Ref T160589

Tanner single phase bandsaw
Max cutting width approx 175mm
340mm throat
355mm x 355mm tilting table
3/4hp motor

3-Phase Industrial Bandsaw

Skylarc Ref Z160959

3-Phase Industrial Bandsaw.
Made in Germany by Petzing & Hartmann Kassel.
Model No. SLA6.3
Uses 4400-4500mm.long, 13-25mm.wide blades (not included).
Blade wheels approx 630mm diameter.
Cutting table approx 845x755mm.
Operational condition unknown.

Heavy Vintage Cast Machined Engineering Table

Skylarc Ref P160741

Heavy Vintage Cast Machined Engineering Table.
Top cast steel piece measures 1980x1070x212mm and is Machined on both top and bottom according to supplier. Approx 130mm semi hollow gap between plates with 50mm diamter support rods spaced 150mm apart on centre. Top plate approx 40mm thick, bottom plate 45mm thick.
Support frame is thick hardwood beams.
Other items see under and around table are not included.

Multi Tool Woodworking Station

Skylarc Ref L160867

Custom made work station
Single phase Craftsman bandsaw (no blade)
Single phase grinder (needs new plug)
Small single phase sander (215mm diameter)
Large three phase sander (460mm diameter)
Mounted on pallet
All stations run

Roller Conveyor System

Skylarc Ref M161388

Heavy duty steel conveyor
650mm wide roller sections
50mm diameter rollers
4 sections
1670mm, 1200mm, 2200mm, 2520mm
Lifting sections
2200mm section has a pneumatic lifting system

Canning Three Phase Polisher/Buffer

Skylarc Ref B159947

Canning Model 16f2
5 hp three phase motor
Various polishing wheels on small table

Heidenhain 3D Touch Probe TS-220

Skylarc Ref O160792

Heidenhain 3D Touch Probe.
Model TS-220.
BT40 type tool mount.
Unknown if item is used. Wood case exterior shows storage dust.

https://www.atechauthority.com/product-details/ts-220

Panelmasta Fly Press

Skylarc Ref Z159945

Manufactured by R.Baverstock
310mm x 215mm table
Approx 90mm travel

Workbench with Vice and Fly Press

Skylarc Ref P159935

Heavy duty wooden workbench
1570mm x 725mm x 830mm tall
Record No.5 vice
R.Baverstock Panelmasta Fly Press
Assorted industrial parts and supplies

Meteor Multi Head Drill

Skylarc Ref I159928

Meteor 4 head drill
Single phase
4 separate pedestal drill units
No.2 morse taper spindles
Approx 100mm spindle travel
4 speeds
Belt drive
265mm x 255mm cast tables
Various chucks etc

Pallet Rotator

Skylarc Ref I159902

1170mm diameter
Three phase
20 amp plug
Foot operated
Forklift slots

Large Bandsaw

Skylarc Ref M160868

Cast iron frame
Three phase
370mm max cut thickness
870mm throat
4kW motor
Tilting table 750mm x 960mm

Whitehead Planer/Thicknesser

Skylarc Ref K160866

Model: Whitehead P.T.J.
Three phase
310mm wide table
Planer on top, thicknesser underneath

Single Phase Belt and Disc Sander

Skylarc Ref J160865

Model: BDS-9
Single phase
3/4 hp motor
6"x9" sanding bed
220mm sanding disc

Morgan Belt Sander

Skylarc Ref D160859

Morgan Wood Sanding Machine
1100 watt motor
Single phase
150mm x 940mm sanding bed

Single Phase Belt and Disc Sander

Skylarc Ref U160590

Single phase
6"x9" sanding bed
310mm sanding disc

Three Phase Belt Sander/Linisher

Skylarc Ref C160572

Cast iron belt sander
350mm x 150mm sanding surface
Three phase
On wooden stand

Sand Mixer

Skylarc Ref O161390

Sand mixer
Unknown make or model
3 phase 4kW motor
Control panel
Pumps and accessories
Buyer will need to decommission

Small Furnace Crucible

Skylarc Ref I161384

Tipping mechanism
400mm x 520mm internal dimensions
570mm x 660mm tall external crucible dimensions

Sand Dryer and Sifter

Skylarc Ref G161382

Rotary sand sifting machine
LPG powered heater
Vibrator
3 phase 1.1kW electric motor

Dependable Core Blower

Skylarc Ref B161377

Dependable Model 100-S
Gas and air operated
40lb sand capacity
Manual

Large Assortment of Tumbler Polishing Stones

Skylarc Ref S161290

Large Assortment of Tumbler Polishing Stones
See Photos for more details

Large Corroded Steel Rack

Skylarc Ref Q161288

Large Corroded Steel Rack

Assorted Lengths of Aluminium and Steel Tubing

Skylarc Ref M161284

Assorted Lengths of Aluminium and Steel Tubing

Large Lot of Cambrian Foundry Valve Moulds

Skylarc Ref P161313

Moulds for various types of valves
Mainly aluminum moulds

Haas Fourth Axis

Skylarc Ref N161493

Haas 4th axis
Unknown model
Previously used on 1998 Haas VF3
Tailstock

Timesavers Industrial Linisher

Skylarc Ref E161484

Timesavers 960-1MW
3 phase
Wet belt grinder/linisher
230mm wide x 700mm belt
Built in vacuum pump
20 amp plug
Some spare belts

30-Drawer Wooden Drawer Cabinet

Skylarc Ref B161169

30-Drawer Wooden Drawer Cabinet.
Wood frame with 29mm thick older type MDF board top.
Top surface is 535mm wide.
Wood drawers with heavy steel handles.
Drawers sit on wood runners, see photos.
Each Drawer interior measures approx 440x430x110mm.
Well built sturdy and very large unit.
Items seen on and around cabinet are NOT included.

5x Large 303 Stainless Steel Rods

Skylarc Ref L161153

5x Large 303 Stainless Steel Rods.
Includes the following sizes:
- 1x 4180mm long, 48mm dia.
- 4x 75mm diameter rods in lengths of 2880mm, 3820mm, 3810mm, and 3900mm.
- also includes a bonus 304 stainless hollow pipe 1175mm long, 50mm diameter.

Condition- As new leftover factory materials supply stock. Rods have rust on them from storage in a very leaky old shipping container.

Large Assortment of Threading Dies

Skylarc Ref Y161270

Large Assortment of Threading Dies

Mitutoyo 2-Axis KA Counter 174-173F, As New

Skylarc Ref V160773

Mitutoyo 2-Axis KA Counter.
Code No. 174-173F.
Measures approx 250x80x170mm.
Includes power cord, some mounting hardware, Instalation manual, original box.
Item appears as new never installed.

Mitutoyo 1400mm Linear Scale 539-291, As New

Skylarc Ref T160771

Mitutoyo 1400mm Linear Scale.
Code No.539-291, AT115-1400
1600mm total unit length.
Includes original paperwork and box.
Item is as new as still wrapped in plastic.

Toko Profile Measuring Projector Type MP-30A

Skylarc Ref R160795

Toko Profile Measuring Projector.
Model Type MP-30A.
Includes a number of accessories and attachments, see photos.
Powers on, fan runs and light operates, not further tested.

Vintage 3-Phase Bandsaw

Skylarc Ref W160956

Vintage 3-Phase Bandsaw.
Made in USA by Gibb & Miller Ltd.
Model No. NS105
Age of Saw unknown.
Blade wheel diameters 455mm.
Hand written note inside blade wheel door states blade length of 3.45 metres. Installed blade has width of 12mm.
Cutting table approx 605x605mm.

Large Industrial Sand Blasting Cabinet by Godfrey Engineering

Skylarc Ref V160955

Large Industrial Sand Blasting Cabinet by Godfrey Engineering.
Model No. Cyclo-Blast 13702
Madei in Australia.
Blasting Cabinet interior approx 1150x850x870mm.
3-Phase.
Condition - This unit appears to be incomplete as side doors are missing and some components are piled inside. Unknown if unit has faults or is repairable.

Large Channel Steel Beam, 12-metre Length

Skylarc Ref K160918

Large Channel Steel Beam.
12-metre Length
Width spprox 300x95mm.
Side thickness approx 15mm, bottom thickness approx 10mm.
Rusty from outside storage.

Mitutoyo Linear Scale AT11-N750

Skylarc Ref N160791

Mitutoyo Linear Scale AT11-N750.
970mm item height.
Unknown if unit is complete, see photos.

Mitutoyo Bore Gauges, 3x Units

Skylarc Ref E160782

Mitutoyo Bore Gauges.
Includes the following Code Numbers:
- 511-106s, 2.4" to 4"
- 511-105n, 1.4" to 2.5"
- 511-104a, 0.7" to 1.4"

All include wood cases.
See photos for details on included accessories, Parts, etc.

Avery 500kg Industrial Scale

Skylarc Ref T160745

Avery 500kg Industrial Scale.
Type No. 3205 CLE
750kg max capacity according to ID plate, 500kg capacity according to dial gauge.
Weighing platform 1260x700mm and 240mm above floor.
Mounted on wheels, rolls foward and back
Operates and reads my weight at 90kg which is about right according to my last doctor visit.
Dirty surfaces from factory, would benefit from a cleanup.

Richards 760mm 3-Phase Snagging Grinder

Skylarc Ref O160948

Richards 760mm 3-Phase Snagging Grinder.
Model number and age unknown.
Includes wall.mounted Nissen Automatic Starter electrical box.
The unit will be decommissioned from power before buyer pickup.

Cammac Single Phase Drill

Skylarc Ref A159946

Cammac 12 speed bench drill press
19mm capacity
120 - 2580rpm spindle speeds
Jacobs No.14N 0-1/2" chuck
305mm table
550 watt single phase motor
80mm spindle travel
No.4 MT spindle
Belt drive

Workbench with Two Vices

Skylarc Ref X159943

Heavy Duty Wooden Workbench
Two vices with rotary bases
6" and 6"1/2"
850mm work top height
Assorted tools and industrial supplies
Fly Press and Drill Press are NOT included

Pneumatic Press on Table

Skylarc Ref U159940

Martonair pneumatic press
On solid timber bench
200mm x 240mm press table
Unknown capacity

Drawer Set with Tooling

Skylarc Ref Y161088

Drawer set with Tooling, includes Saw Blades, Dies, Drill Bits, Lathe Tooling.
See photos for more details

Mitutoyo Linear Scale 539-275

Skylarc Ref U160772

Mitutoyo Linear Scale.
Code No. 539-275, AT115-300
480mm item length.
Includes original box.
Item appears as new never installed.

Cabinet of Drills, Taps, Tooling

Skylarc Ref U159914

15 drawer cabinet
Contents include
Spotting drills
Taps.
Dies
Drill bits
Cutters

T-Slot Block Stand

Skylarc Ref O159908

T slot drill block
25mm slots
Cast

Antique Workshop Cabinet

Skylarc Ref N159907

Vintage two door cabinet
5 levels
Looks like Rimu
Great patina

Cabinet of Welding Rods

Skylarc Ref M159906

Old drinks fridge used at welding cabinet
Huge range of rods
Gouging rods
Low hydrogen rods
Cobalarc rods
CI Soft Flow NI
And more

Drawer Set with Tooling

Skylarc Ref O161078

Drawer set with Tooling, includes Grub Screws Nuts Washers, Dies, Drill Bits, Lathe Tooling.
See photos for more details

Drawer Set with Tooling

Skylarc Ref N161077

Drawer set with Tooling, includes Die Heads, Tension Pins, O Rings, Brass Collets and other Lathe Accesories
See photos for more details

Digi Counting Scale DC-180 w/ Expansion Scale

Skylarc Ref S160744

Digi Counting Scale DC-180.
5kg capacity of main unit.
300x230mm stainless steel tray.
Includes a secondary larger accessory Scale, model DS-410, with 150kg capacity and 400x400mm top surface.
Operates but not tested for accuracy.

Avery Industrial 110kg Dial Scale

Skylarc Ref R160743

Avery Industrial 110kg Dial Scale.
Type No. 3205 CLE
Dial states 110kg max capacity, ID label states 170kg capacity, see photos.
Weighing platform 780x700mm and 230mm above floor.
Operates and appears accurate (last checkup stated I weighed 89kg as this scale indicates, see photo.)
Dirty surfaces from industrial factory, would benefit from a cleanup.

Single Phase Overhead Router

Skylarc Ref A160856

Towa Electric R-320 Heavy Duty Router
Single phase
24000rpm
Very heavy cast table
Adjustable height

Single Phase Bobbin Sander

Skylarc Ref E160600

Wadkin Bobbin Sander
Single phase
660mm x 650mm cast table
Tilting rise and fall table
Mounted on pallet
Runs but motor trips after a few seconds

Tauco Combination Table Saw and Planer

Skylarc Ref W160592

Tauco Combination Table Saw and Planer
Three phase
685mm x 505mm tilting saw table
165mm wide planer table
Made in the USA

Vintage Milling Machine

Skylarc Ref D161015

This is a vintage "Corona" milling machine manufactured by Fredk Pollard & Co. Ltd., Leicester, England, model 9FX. It features belt-driven speed adjustments with RPM ranges from 2,700 to 18,000 depending on the belt position. The attached motor is labeled B.S.S. Lancashire Crypto, with specifications for 230/400V, 3-phase power, and a max speed of 2,820 RPM.

Cincinnati Horizontal Milling Machine

Skylarc Ref B160545

Cincinnati horizontal mill
460mm x 170mm T slot table
Three phase
10 spindle speeds
75 - 1100rpm
Rotary collet vise
Coolant pump

Industrial Sand Bladting Cabinet w/ Ironside Air Blasting Gun

Skylarc Ref X160957

Industrial Sand Bladting Cabinet.
Includes Ironside Air powered sand Blasting Gun, model number unknown.
Blasting Cabinet interior approx 580x590x580mm.

Industrial Shaker Bin

Skylarc Ref T160953

Industrial Shaker Bin.
Unknown brand/model.
Thick hard rubber Bin approx 960mm diameter, 310mm deep.
500V, 10A 3-phase plug
Note that base is missing a suport spring.

Industrial Shaker Bin

Skylarc Ref S160952

Industrial Shaker Bin.
Manufactured in Australia by Selman & Howel Ltd.
Model and age unknown.
500V, 20A 3-phase plug.
Steel bin approx 590x285mm and 250mm deep.
Drive Belts from motor to Bin Shaker assembly are missing.

Furnace and Control Systems

Skylarc Ref J161385

Foundry furnace
1200mm diameter
1570mm tall
430mm internal diameter x 650mm deep
Red lion control panel
Will be electrically disconnected
Buyer will need to physically decommission

Heavy All Steel Workbench Table

Skylarc Ref L160919

Heavy All Steel Workbench Table.
75x75mm ox Steel legs.
Approx 18mm thick 2-ply Steel plate top surface.
Lower shelf with approx 3mm thick steel sheet surface
Top surface e has a 1265x515mm steel sheet welded oddly in the centre of the Workbench, see photos.
Rusty from outdoir storage but still a strong unit.

Honing Machine on Bench

Skylarc Ref V161345

Delapena Precision Honing Machine
Has been modified and not used for honing
Single phase
Mounted on table

Large Lot of End Mills

Skylarc Ref F161329

Approx 100 total

David Brown Adjustable Floating Reamer

Skylarc Ref N161311

David Brown Adjustable Floating Reamer S8
34.9mm - 38.1mm
No.2 morse taper
https://www.engineeringsupplies.co.uk/349mm-381mm-s8-tct-david-brown-reamer.html

David Brown Adjustable Floating Reamer

Skylarc Ref M161310

David Brown Adjustable Floating Reamer S11
50.8mm - 60.3mm
No.4f morse taper
https://www.engineeringsupplies.co.uk/508mm-603mm-s11-hss-david-brown-reamer.html

David Brown Adjustable Floating Reamer

Skylarc Ref L161309

David Brown Adjustable Floating Reamer S11
50.8mm - 60.3mm
No.4f morse taper
https://www.engineeringsupplies.co.uk/508mm-603mm-s11-hss-david-brown-reamer.html

David Brown Adjustable Floating Reamer

Skylarc Ref K161308

David Brown Adjustable Floating Reamer S11
82.5mm - 101.6mm
No.4 morse tapert
https://sheffieldtooling.co.uk/browse-by-category/hole-making/reamers/david-brown-floating-reamers/david-brown-floating-reamer-s14-82-5-101-6mm/

Assorted Aluminium Lengths, Cylinders

Skylarc Ref M161154

Assorted Aluminium Lengths, Cylinders.
Includes the following bar lengths:
- 8x 2400x100x30mm
- 1x 1280x82x25mm.

Includes solid cylinder sizes:
- 2x 1500mm long, 130mm dia.
- 1x 1710mm.long, 100mm dia.
- 1x 1000mm long, 75mm dia.
- 1x 995mm long, 50mm dia.
- 1x 685mm long, 60mm dia.
- 1x 940mm long, 60mm dia.
- 2x 585mm long, 75mm dia.
- 1x 375mm long, 75mm dia.

Two hollow lengths, one 35x35mm square by 665mm long snd 75mm diameter pipe 1470mm long.

Leftover factory material supply stock. Some rust and tarnishing on surfaces from storage in a rusty leaking steel container.

Microsoft Surface Tablet w/ Docking Station

Skylarc Ref H161149

Microsoft Surface Tablet w/ Docking Station.
Processor is Intel Core i5-4300U at 2.50GHz.
8Gb RAM.
256Gb storage, wiped of old user data.
Windows 10 Pro reset for new user setup.
Includes charging cable and Microsoft Surface Docking Station stand.

Mitutoyo Interchangable Anvil 150-300mm Micrometer 104-136

Skylarc Ref S160770

Mitutoyo Interchangable Anvil 150-300mm Outside Micrometer.
Code No.104-136
See photos for included accesories.
Wood case shows some exterior damage.

Mobile Workshop Workbench Table

Skylarc Ref M160920

Mobile Workshop Workbench Table.
Box Steel frame with 2mm thick steel top work surface.
150mm diameter castors.
Rusty surfaces from outdoor storage but still a sturdy unit. Castors seem to roll ok.

Heavy Steel Materials Storage Rack

Skylarc Ref I160916

Heavy Steel Materials Storage Rack.
200x70mm channel steel base feet.
155x75mm I-Beam vertical frame.
50mm diameter hollow steel pipe angled support tubes each approx 590mm long with pvc pipe covering.
Rusty from outdoor storage

Mitutoyo Digital Height Gauge 192-607

Skylarc Ref V160799

Mitutoyo Digital Height Gauge.
Model 192-607.
610mm max measuring height.
800mm device height.

Outside Micrometer, 400-500mm Size

Skylarc Ref T160797

Outside Micrometer, 400-500mm Size.
Unknown manufacturer.
Wood case.

Mitutoyo Digital Height Gauge 192-613

Skylarc Ref S160796

Mitutoyo Digital Height Gauge model 192-613.
475mm device Height.
300mm max measuring Height.

Vintage Portable Precision Engineers Table, 305x205mm

Skylarc Ref L160789

Vintage Portable Precision Engineers Table.
Unknown manufacturer.
Table surface 305x205mm.
Adjustable feet.
Wood top cover, one Latch loop is missing on cover.

300mm Height Gauge

Skylarc Ref R160769

300mm Height Gauge.
Unknown manufacturer and model.
Includes wood case.

Assorted Mitutoyo Precision Tools, Calipers, Gauges & More

Skylarc Ref Q160768

Assorted Mitutoyo Precision Tools, Calipers, Gauges & More.
Includes the following:
- Vintage Universal Vernier Caliper 190-101
- Groove Micrometer 146-102
- 35mm Dial Caliper 209-101
- 12mm thick x 45mm diameter Optical Flat 158-117.
- Internal Micrometer 0.2" to 1", unknown code number.
- Case of unknown Mitutoyo items, see photos.

Condition varies with each item

6x Vintage Moore & Wright Outside Micrometers

Skylarc Ref J160761

6x Vintage Moore & Wright Outside Micrometers.
Includes:
- No. 941x, 0" to 4" set
- No. 966, 3" to 4"
- No. 966/3, 3" to 4" (in a Starrett Branded case).
- No. 969, 4" to 5"
- No. 970, 5" to 6"
- No. 971/7, 6" to 7"

See photos for included accessories, condition.

Galvanised Steel Racking with Contents

Skylarc Ref I161072

Galvanised Steel Shelving with Contents,
See photos for more details

Hydraulic Power Pack

Skylarc Ref F161069

Hydraulic Power Pack, Unkown Specifications. Manufactured by NACHI
Model No.UVD-1A-A3-1.5-4-1410

Galvanised Steel Racking with Contents

Skylarc Ref E161068

Galvanised Steel Shelving with Contents,
See photos for more details

Galvanised Steel Racking with Contents

Skylarc Ref C161066

Galvanised Steel Shelving with Contents,
See photos for more details

Galvanised Steel Racking with Contents

Skylarc Ref B161065

Galvanised Steel Shelving with Contents,
See photos for more details

Galvanised Steel Racking with Contents

Skylarc Ref Y161062

Galvanised Steel Shelving with Contents,
See photos for more details

Avery Vintage Self Indicating Counting Scale 1208 GFD

Skylarc Ref Q160742

Avery Vintage Self Indicating Counting Scale.
Model No. 1208 GFD, 69645/1
Weight capacities are unknown.
Moving parts seem to move easily and smoothly.
Main basin approx 550x300mm.
Dirty from factory exposure, would benefit from a cleanup.
Includes the vintage Wood platform it sits on.

Vintage Meteor Single Phase Drill Press w/ Cabinet

Skylarc Ref O160740

Vintage Meteor Single Phase Drill Press w/ Cabinet.
Drill model No. 40/005
Drill approx 1020mm tall.
Vice Table 265x265mm.
Foot actuated control pedal on floor.
Includes Record branded Drill vice.
Includes heavy Duty Steel Framed wood topped table 680x635x900mm.
Includes storage cabinet within table.
Operates but shows heavy wear and usage. Drill motor appears to be a newer replacement unit.

Wooden Workbench with Vices

Skylarc Ref F160861

Heavy duty wooden workbench
800mm x 1800mm top
2 x Record wood working vices

Worksite Toolbox and Power Tools

Skylarc Ref M160582

ToolPRO worksite toolbox
Assorted power tools
Grinder
Impact driver
Skill saw
Drill
Chain block

Elliot 6" Universal Driving Head Lathe Chuck Assembly

Skylarc Ref E160704

Elliot 6" Universal Driving Head Lathe Chuck Assembly.
160mm diameter chuck face.
Mounting bolt hole slots spaced approx 200mm apart on centre.
Includes Chuck key.
Operational condition is unknown.

12x Mitutoyo Micrometer Setting Standards, 25mm to 300mm

Skylarc Ref W160982

12x Mitutoyo Micrometer Setting Standards.
Includes the following Mitutoyo part numbers / lengths:
- 167-101, 25mm
- 167-102, 50mm
- 167-103, 75mm
- 167-104, 100mm
- 167-105, 125mm
- 167-106, 150mm
- 167-107, 175mm
- 167-108, 200mm
- 167-109, 225mm
- 167-110, 250mm
- 167-111, 275mm
- 167-112, 300mm

All appear either unused or very lightly used.

Vintage Union Inverted Stereo Microscope

Skylarc Ref M160972

Vintage Union Inverted Stereo Microscope.
Made in Japan.
Model BI-9562
Optics include 5x, 10x, 20x and 40x
Light assembly is operational.
Overall measures approx 340x200x220mm
Top table 120x120mm in size.
A heavy well built vintage unit.

Large Assortment of Old Engineering Parts

Skylarc Ref P160533

Large Assortment of Old Engineering Parts and Accessories

Shelving and Contents

Skylarc Ref Y160516

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref B160519

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref A160518

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref Z160517

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref X160515

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref W160514

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref V160513

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref U160512

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref T160511

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref S160510

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included

Shelving and Contents

Skylarc Ref R160509

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included

Shelving and Contents

Skylarc Ref P160507

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref O160506

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref N160505

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref M160504

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref L160503

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref K160502

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref J160501

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref Q160508

Shelving and Contents
Shelving is 2400mm tall and long and 500mm deep
Made from Galvanised Steel. Shelving has 5 Levels.
Any Files are NOT included
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref C161300

Shelving and Contents
Shelving is 2400mm tall and long and 300mm deep
Made from Galvanised Steel. Shelving has 3 Levels.
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref B161299

Shelving and Contents
Shelving is 2400mm tall and long and 300mm deep
Made from Galvanised Steel. Shelving has 3 Levels.
Located upstairs
Buyer will need to unload the shelving themselves

Shelving and Contents

Skylarc Ref A161298

Shelving and Contents
Shelving is 2400mm tall and long and 300mm deep
Made from Galvanised Steel. Shelving has 3 Levels.
Located upstairs
Buyer will need to unload the shelving themselves

Steel Shelving

Skylarc Ref Z161297

Shelving is 2400mm tall and long and 300mm deep
Made from Galvanised Steel. Shelving has 3 Levels.
Located upstairs

Shelving and Contents

Skylarc Ref Y161296

Shelving and Contents
Shelving is 2400mm tall and long and 300mm deep
Made from Galvanised Steel. Shelving has 3 Levels.

Shelving and Contents

Skylarc Ref X161295

Shelving and Contents
Shelving is 2400mm tall and long and 300mm deep
Made from Galvanised Steel. Shelving has 3 Levels.

Steel Tubing

Skylarc Ref K161282

Assorted Lengths of Steel Tubing

3x Assorted Steel Lengths

Skylarc Ref J160917

3x Assorted Steel Lengths.
Includes:
- Angle steel length approx 4840mm Ling, 125x125mm wide, and 10mm thick.
- Box Steel length approx 3240mm long, 200x200mm wide, 10mm thick.
- Channel Steel length approx 3270mm long, 250x90mm wide, and from 15mm to 10mm thick.

Items rusty from outdoor storage

Assorted Lengths of Steel Tubing

Skylarc Ref L161283

Assorted Lengths of Steel Tubing
Longest Length is 8 metres

Quick Knurling Tool

Skylarc Ref L161335

Quick-STR 0
3/4" shank
Assorted new and used wheels
Manual

Milling Machine Adjustable T Slot Table

Skylarc Ref C161326

250mm x 225mm table surface
Approx 24mm T slots
Adjustable angle
Rotary base

Desktop Computer w/ Intel 10th Gen Processor & Windows 10 Pro

Skylarc Ref R161185

Custom Desktop Office Computer w/ Intel 10th Gen Processor & Windows 10 Pro
Processor is 10th Gen Intel Core i3-10100 at 3.60GHz
16Gb RAM (2x Crucial 8Gb 2666MHz DIMMS).
Samsung M2 980 SSD drive with 500Gb storage, wiped of old user data.
Microsoft Windows 10 Pro reset for new user setup.
Intel.UHD Graphics 630 integrated GPU.
Asus Prime H510M-E Micro ATX Motherboard.
Antec VP500P Plus PSU
Optical disk drive installed.
Antec branded mid-tower case 395x173x173mm.
Includes Logitech wireless keyboard and mouse.
Includes power cord.
Monitor NOT included.
Mouse and keyboard show some usage wear.
Mild dust within case and fan screens.

Custom Made Table Saw

Skylarc Ref P161261

Custom Made Table Saw
Three Phase with single phase light
Blade width is max 300mm

Large Assortment of Internal Door Hardware

Skylarc Ref M161258

Large Assortment of Internal Door Hardware.

Assorted Multi Head Drills Etc

Skylarc Ref Y159944

7 assorted multi drill heads
Bin of collets
Damaged tapmatic tapping heads
Bin of accessories

Exacta Reclining Press

Skylarc Ref V159941

Exacta flywheel reclining press
Three phase
Unknown capacity but estimate approx 15 ton
20 amp plug

Benchtop Precision Steel Engineering Flat Table

Skylarc Ref I160786

Benchtop Precision Steel Engineering Flat Table.
Unknown manufacturer.
590x370mm. 745mm total length.
Includes wooden cover.

Small Press

Skylarc Ref N159933

Small flywheel press
Three phase and pneumatic
Unknown capacity

Antique Wooden Cabinet and Contents

Skylarc Ref M159932

Solid timber industrial style cabinet
Cabinet height excluding backboard 1040mm
Timber top with hardboard overlay
Contents of tools, drill bits, threading dies
Awesome patina
Great for conversion to a kitchen unit

Modified Pacera Pedestal Drill

Skylarc Ref J159929

Pacera MF4 drill press
Modified for automating a twin drilling process in brass
Two range gearbox
Belt drive
Three phase
Twin drill head

Large Assortment of Taps

Skylarc Ref Z161089

Large Lot of Taps

Mitutoyo Micrometers, 6x Assorted Sizes

Skylarc Ref A160778

Mitutoyo Micrometers.
Includes the following Code numbers:
- 101-103, 0-25mm (2x units).
- 101-104, 25-50mm
- 102-217, 0-25mm
- 103-137, 0-25mm
- 103-138, 25-50mm

Forklift Cage

Skylarc Ref E159898

Universal Handling Equipment AP 5
400kg capacity

5x Assorted Vintage Micrometers & Calipers

Skylarc Ref K160762

5x Assorted Vintage Micrometers & Calipers.
Includes:
- CEJ Sweden Outside Micrometer 109E, 7" to 8"
- Shardlow England Outside Micrometer 54CX, 4" to 5".
- NSK Japan Inside Micrometer set No. 704-304, 1000mm.
- Chesterman, England 7" Vernier Calipers.
- Asian branded 25-50mm Outside Micrometer.

Condition varies with each item.

Metal Cabinet with Lathe Accessories.

Skylarc Ref M161076

AHI Precision 3 Drawer Cabinet containg a mixture of J/Chucks, Machine Tool Holders and Morse Adadpters.
See photos for more details.

Metal Cabinet with Lathe Accessories.

Skylarc Ref L161075

AHI Precision 3 Drawer Cabinet containg a mixture of J/Chuck Keys, Lathe Chuck Keys, Boring Bars and Live and Dead Centre's.
See photos for more details.

Automatic Extrusion Cutoff Saw

Skylarc Ref X160879

Custom made aluminum saw
Automatic for cutting long lengths of profile
Three phase
Pneumatic feeds
Has been modernized at some point

Geo-Tek NAL24 Survey Level w/ Tripod & Ranging Pole

Skylarc Ref V160747

Geo-Tek NAL24 Survey Level w/ Tripod & Ranging Pole.
Level unit includes case.
Last calibration was in 2015.

Lincoln TIG/ARC Welder on Trolley

Skylarc Ref W160878

Lincoln Electric Invertec V250-S
TIG/ARC Welder
Single phase
TIG gun
ARC electrode
250 amp max welding output
On trolley

IK-12 BEETLE

Skylarc Ref D161067

IK-12 BEETLE
Unknown if complete, item has not been tested so unsure if works.

Somet 1000mm Vernier Caliper

Skylarc Ref U160746

Somet 1000mm Vernier Caliper.
Includes case.
Some surface rust spotting on Tool.

Cabinet and Contents

Skylarc Ref O160870

MDF workbench
Contents include
strapping equipment
Electrical supplies
Drills
Hose clips
Bolts and nuts
Dyna bolts

CNC Machine Vice by Trulok

Skylarc Ref H160733

CNC Machine Vice by Trulok.
155mm wide jaws.
Opens to approx 155mm.
Swivel base with mounting bolt slots spaced 300mm apart on centre.
Includes hand crank tool.
Shipping not available due to item being over the max weight limit of our courier.

Large Disc Sander

Skylarc Ref D160599

605mm sanding disc
Three phase 32 amp plug

Large Cabinet of Industrial Supplies

Skylarc Ref B160597

Large steel shelving unit
Contents include
Tools
Gas torch
Power tools
Various bits and pieces

Workshop Cabinet and Contents of Tooling

Skylarc Ref Y160594

Wooden cabinet
Contents include
Drill bits
Small 3 jaw chuck
Machine tooling
Holesaws
Taper adaptors

Cabinet Shelf Unit and Contents of Industrial Supplies

Skylarc Ref X160593

Steel shelving with integrated cabinet
Contents include
Electrical supplies
Air drill
D-Weld powder
Bearings
Winches (unknown condition)
Buyer will need to unload the shelves themselves

Large Disc Sander

Skylarc Ref V160591

769mm sanding disc
Three phase 16 amp plug

7 x Annular Cutters

Skylarc Ref N160583

Smallest size 13mm
Largest size 50mm

Workshop Cabinet

Skylarc Ref W161008

Workshop Cabinet and Benchtop
Includes items inside the cabinet but DOES NOT include the items on top of the Cabinet.
See photos for more details

Mitutoyo Spring Calipers

Skylarc Ref X161399

Mitutoyo Spring Calipers includes
1 x Outside Spring Caliper
1 x Inside Spring Caliper
1 x Spring Divider
6" 150mm
Made In Japan

Dare E-90 Tool Sharpener Single Phase

Skylarc Ref Z160543

A Darex E-90 precision tool sharpener, designed for grinding and sharpening various cutting tools. Powered by a 1/4 HP motor, operating at 230V, with adjustable speed options (2800 or 3400 RPM). Includes an adjustable sharpening fixture for precise operation.

Darex Drill Sharpener Single Phase

Skylarc Ref T161395

A Darex Drill Sharpener Single Phase

2x Bowers Metrology 500mm Bore Gauge Extensions

Skylarc Ref R160977

2x Bowers Metrology 500mm Bore Gauge Extensions.
Each is 500mm long, 25mm diameter.
MDF cases.
One case Latch is damaged.

Foundry Sand Mixer

Skylarc Ref N161389

Unknown make and model
Three phase
Control panel
Hopper
Buyer will need to decommission

Pallet Racking and Contents

Skylarc Ref L161387

Single bay of racking
Contents include various timber Aluminum stands
Fan
Buyer to dismantle

Trolley of Cast Ingots

Skylarc Ref F161381

3 wheeled steel trolley
Contents of cast ingots

Trolley of Cast Ingots

Skylarc Ref E161380

3 wheeled steel trolley
Contents of cast ingots

Trolley of Cast Ingots

Skylarc Ref D161379

3 wheeled steel trolley
Contents of cast ingots

Sand Grinder

Skylarc Ref C161378

Nagoyakiko MSU20
Three phase
730mm diameter bowl

Custom Made Core Blower

Skylarc Ref A161376

Gas and air operated
Unknown capacity

Large Lot of Foundry Core Boxes

Skylarc Ref Y161374

Approx 40 total
Steel and aluminum boxes
Sizes from 360mm x 280mm to 530mm x 420mm

Jasic Super Inverter Welder XM200 Pro

Skylarc Ref V160929

Jasic Super Inverter Welder.
Model No. XM200 Pro
Single Phase.
Includes Welder Trolley and attached cables.

Cast Iron Core Blower Boxes

Skylarc Ref W161372

Approx 55 total
Assorted shapes
Cast iron

Large Lot of Aluminum Foundry Plates

Skylarc Ref T161369

21 approx 750mm x 490mm
53 approx 360mm x 290mm
5 approx 440mm x 320mm

Cabinet with Engineering Parts

Skylarc Ref W161294

Cabinet with Engineering Parts, cabinet is made of wood and has an upper and lower compartment.

Pollard Multi Drill

Skylarc Ref R161367

Model: Pollard Corona 12MX Multidrill
Three phase
420mm x 300mm cast table

16 Foundry Ladles

Skylarc Ref V161293

16 Foundry Ladles, Varying Sizes, Most have a handle size of 750mm

2 Crucibles

Skylarc Ref U161292

2 Crucibles
One is older looking and has no legible markings and stands at 440mm tall. The base is 200mm in diameter and the top is 330mm. internal depth is 300mm. Unknown Material.

The other Crucible is newer but still used, writing states "A 80" and "58 06/22". Crucible stands at 400mm tall and has a base diameter of 200mm which extends to 310mm at the top. Internal depth is 300mm. Unknown Material Combination but appears to be Clay type (could be silicon carbide. could be graphite clay).

Migatronic Single Phase TIG Welder

Skylarc Ref R160925

Migatronic Single Phase TIG Welder.
Model No.Focus TIG 200 DC PFC
Includes Cabling, see photos.
Welder unit appears in Good condition, powers on but not further tested. Cables show duct tape "repairs" on parts of the cables so cables may need replacing.

Ensitech TIG Brush TBX-300

Skylarc Ref Q160924

Ensitech TIG Brush TBX-300.
Includes black and red connecting cables, power cord, quickstart guide, and ToolPro hardcase.
Unit turns on but not further tested. Connecting cables have corrosion on plug ends, see photos.

Old Conveyor Rollers

Skylarc Ref R161289

Old Conveyor Rollers

Vintage Hravy Duty Workbench

Skylarc Ref O160922

Vintage Hravy Duty Workbench.
50x50mm angle steel frame.
Wood board top and lower surfaces.
Top surface approx 890mm above floor.
380mm high steel backsplash.
Shows some weathering and rust from outdoor storage but still a sturdy unit.

40' Shipping Container with Contents

Skylarc Ref J161281

40' Shipping Container
In terrible shape. Will most likely need to be Cut up to remove. Contents include slot of Waste Water Filters

Large Lot of Drill Bits and Taps

Skylarc Ref M161336

Mainly metric sizes
Largest drill 21.1mm
Metric taps mainly 10mm x 1.5mm
Surface rust on some drills

Two Pallets of Foundry Supplies

Skylarc Ref J161333

Sleeve risers
Filters ceramic foam
Assorted styles

Steel Cabinet

Skylarc Ref V161319

Heavy duty steel cabinet
470mm x 480mm work table off side
Contents of assorted tools etc

150kg Winch Stacker

Skylarc Ref S161316

Universal Handling Equipment
150kg capacity
530mm x 500mm removable platform
1020mm max lift height

Large Lot of Vintage Home Hardware Foundry Moulds

Skylarc Ref Q161314

Ornamental and vintage homeware hardware
Mainly aluminum moulds
Drawer pulls, handles etc

Vintage Safe by Thomas Skidmore & Son, England

Skylarc Ref S161186

Vintage Safe by Thomas Skidmore & Son, England.
Age unknown.
Vintage key included for main door and mechanisims appear to be operating.
Main internal chamber is approx 460x445x475mm.
Two lockable drawers each spprox 400x210x90mm. Key for these inner drawers is missing.
Vintage safe in overall very good functioning condition.

Vintage Wooden Cabinet and Contents

Skylarc Ref P161495

Timber multidraw cabinet
Shelves one side
Contents include thread chasers and assorted industrial supplies
Great project to convert for the kitchen

Chamfering Deburring Cutter by Vertex

Skylarc Ref Z161167

Chamfering Deburring Cutter by Vertex.
Model number unknown.
Single Phase 10A plug.
Cutting surface 495mm long, 102mm wide.
See photos for blade type attached details.
Powers on and runs quietly.

6x Decommisioned Electric Gantry Trolley Hoists

Skylarc Ref O161156

6x Decommisioned Electric Gantry Trolley Hoists.
Elephant 2x 2-ton and 1x 1-ton units, Demag 2.5-ton, Nitchi 1-ton, and Kito 1-ton.
All are decommisioned well used units needing extensive repairs or scrap use.
Specific faults on each are unknown.

Large Lot of Machine Tooling

Skylarc Ref V161241

Machine tooling new and used
Mostly packaged

Large Lot of Machine Tooling

Skylarc Ref U161240

Machine tooling new and used
Mostly packaged

Large Lot of Machine Tooling

Skylarc Ref T161239

Machine tooling new and used
Mostly packaged

Large Lot of Machine Tooling

Skylarc Ref S161238

Machine tooling new and used
Mostly packaged

Large Lot of Machine Tooling

Skylarc Ref R161237

Machine tooling new and used
Mostly packaged

Large Lot of Machine Tooling

Skylarc Ref Q161236

Machine tooling new and used
Mostly packaged

Large Lot of Machine Tooling

Skylarc Ref P161235

Machine tooling new and used
Mostly packaged

Large Lot of Machine Taps

Skylarc Ref O161234

Machine Taps
34 taps
A few cutters

14 Heavy Duty Galvanised Eye Bolts

Skylarc Ref J161255

14 Heavy Duty Galvanised Eye Bolts
210mm x 40mm bolt
360mm length total
Eye is 150mm x 100mm and is 30mm thick steel with a hole size of 90mm x 40mm

3x 250mm Engineers Bubbe Levels

Skylarc Ref P160793

3x 250mm Engineers Bubbe Levels.
Two are Kinex branded
Third unit is unknown brand.
All have wooden cases.

Precision Engineers Glass Surface Block, 305x305x25mm

Skylarc Ref M160790

Precision Engineers Glass Surface Block.
Unknown manufacturer.
Block measures 305x305x25mm.
Wood case.

Mitutoyo 300mm Dial Caliper

Skylarc Ref K160788

Mitutoyo 300mm Dial Caliper.
Model.number unknown.
Tool in good condition, dial.operarss but not tested for accuracy. Plastic case shows heavy wear.

Vintage Skoda Benchtop Precision Engineers Table, 500x400mm

Skylarc Ref H160785

Benchtop Precision Engineers Table.
No manufacturer plate attached though a vintage Skoda symbol is forged onto the underside, see photos.
No top cover included, top surface is rusty.

Mitutoyo Micrometers, 2x Units, Blade & Standard Varieties

Skylarc Ref Z160777

Mitutoyo Micrometers.
Includes Code Numbers:
- 122-101 Blade Micrometer 0-25mm
- 102-217, 0-25mm

Plastic cases show more moderate wear. Tools inside in very good condition and turn smoothly but accuracy not tested

Mitutoyo Micrometers, 3x Units

Skylarc Ref X160775

Mitutoyo Micrometers.
Includes:
- 2x units of 103-140, 75-100mm
- 1x unknown code number unit, someone hand wrote 50-75mm on its case.

Cases show heavy wear.

Venture Speed Dial Indicator Set

Skylarc Ref P160767

Venture Speed Dial Indicator Set.
70mm diameter dial face.
Adjustable speed dial.
Includes wood case.
Appears to operate but accuracy not tested.

Mitutoyo Depth Micrometers, 2x Units

Skylarc Ref N160765

Mitutoyo Depth Micrometers
Includes:
- 129-112, 0-150mm
- 129-109, 0-50mm

Some accessories may be missing, see photos.
Case is damaged for smaller unit.

Assorted Vintage Starrett Branded Micrometers

Skylarc Ref M160764

Assorted Vintage Starrett Branded Micrometers.
Includes:
- Mul-T Anvil Micrometer No. 220
- Outside Micrometer No. 436, 2" to 3"
- Inside Micrometer set, Part number unknown.

All are older units.

6x Vintage Moore & Wright Outside Micrometers

Skylarc Ref I160760

6x Vintage Moore & Wright Outside Micrometers.
Includes:
- 2x No. 966, 1" to 2"
- No. 966/2, 1" to 2"
- No.968, 2" to 3"
- No. 966/4, 3" to 4" (No case).
- No.965, 0" to 1" (no case).

Condition varies with each unit.

Depth and Inside Micrometers by Moore & Wright and Shardlow

Skylarc Ref H160759

Assorted Depth and Inside Micrometers by Moore & Wright and Shardlow.
Includes:
- 2x sets of Shardlow branded Depth micrometers in Moore & Wright cases.
- Moore & Wright Depth micrometre set No.54
- Moore & Wright Inside Micrometer set No. 53.

Condition varies with each item. One Shardlow Micrometer is missing its Depth shank. Some accessoriea are missing, see photos.

Set of Imperial Pin Gauges, 0.061" to 0.25"

Skylarc Ref B160753

Set of Imperial Pin Gauges.
Unknown mamufacturer.
Sizes from 0.061" to 0.25".
Appears to be 8x pins missing, see photos.
Wood case but lid is missing.

Set of Imperial Pin Gauges, 0.252" to 0.498"

Skylarc Ref A160752

Set of Imperial Pin Gauges.
Unknown manufacturer.
Sizes included from 0.252" to 0.498"
About 7x pins are missing, see photos
Wood case but lid is missing

Set of Imperial Pin Gauges, 0.501" to 0.581"

Skylarc Ref Z160751

Set of Imperial Pin Gauges.
Unknown manufacturer.
Sizes included from 0.501" to 0.581"
One pin is missing, see photos
Wood case but lid is missing

Set of Imperial Pin Gauges, 0.582" to 0.651"

Skylarc Ref Y160750

Set of Imperial Pin Gauges.
Unknown manufacturer.
Sizes included from 0.582" to 0.651"
One pin is missing, see photos
Wood case but lid is missing

Set of Imperial Pin Gauges, 0.652" to 0.711"

Skylarc Ref X160749

Set of Imperial Pin Gauges.
Unknown manufacturer.
Sizes included from 0.652" to 0.711"
Wood case but lid is missing

Set of Imperial Pin Gauges, 0.712" to 0.75"

Skylarc Ref W160748

Set of Imperial Pin Gauges.
Unknown manufacturer.
Sizes included from 0.712" to 0.750"
One pin is missing, see photos.
Wood case but lid is missing

Vintage Steel Stamp Set, Size 1/16"

Skylarc Ref F161017

Vintage Steel Stamp Set.
Made in England in 1970 by Edward Pryor & Son Ltd
1/16" Size stamps.
Wood case approx 170x150x30mm.
Some stamps are missing, see photos. Wood case shows heavy external wear, One latch broken

Vintage Steel Stamp Set, Size 3/32"

Skylarc Ref E161016

Vintage Steel Stamp Set.
Made in England in 1970 by Edward Pryor & Son Ltd
3/32" Size stamps.
Wood case approx 170x150x30mm.
See photos for more information.
Wood case shows heavy external wear.

Workshop Scrap Metal Bin Trolley

Skylarc Ref H160707

Workshop Scrap Metal Bin Trolley.
Total length with handle 1140mm.
Inner Bin depth 510mm.
Rolls easily.

24" 600mm Crescent Adjustable Wrench

Skylarc Ref F160705

24" 600mm Crescent Adjustable Wrench.
Made in USA by Crescent Tool Co.
630mm total Tool length.
Jaws operate smoothly.

Workshop BT40 / CAT40 Tool Holding Trolley Cart w/ Vices

Skylarc Ref B160701

Workshop BT40 / CAT40 Tool Holding Trolley Cart w/ Vices.
700mm length with a 280mm steel shelf added to one end.
Holes in top surface approx 50mm diameter and on middle surface 45mm diameter.
Includes BT40 or similar size Tool vice plus a Record No.8 bench vice.
Well used but sturdy unut that rolls well.

Makita Corded 180mm Angle Grinder GA7060

Skylarc Ref E160990

Makita Corded 180mm Angle Grinder.
Model No. GA7060
Includes side handle and disk guard.
Disk changing tool is included, see last photo

Assorted Vintage Gauge Blocks, Roughness Sample Plates, & More

Skylarc Ref U160980

Assorted Vintage Gauge Blocks, Roughness Sample Plates, & More.
Includes:
- Vintage Robert & Co, England Microsurf No.319 face turning gauge sample set.
- Vintage Baroid Part No. 992-02 Fineness of Grind Gauge.
- Vintage Matrix Ikeche, England, Steel block gauge set.
- 72x50x25mm glass block with T013 etched into it.
- Imperial Size wavy parallel Set.
- 14x Assorted loose steel gauge blocks.

Condition and age varies with each item.

2x Sylvac Capacitive Measuring Probes P-10

Skylarc Ref Q160976

2x Sylvac Capacitive Measuring Probes.
Both are Model P-10.
Unknown if units are used.
Sed the manufacturer website below for further specs:
https://www.sylvac.ch/product/capacitive-measuring-probes/

All Steel Workshop Workbench Table

Skylarc Ref N160921

All Steel Workshop Workbench Table.
65x65mm box steel legs
5mm thick steel top surface.
Rusty from outdoor storage but still a very solid unit

Vintage Pre-V-Dex 11-Drawer Steel File Cabinet

Skylarc Ref Y160906

Vintage Pre-V-Dex 11-Drawer Steel File Cabinet.
Accommodates A4 size files with punch holes along side, see photos.
Appears that a few drawers are not original to this unit as they have different color front panels, see photos.
Condition - Overall good condition for this vintage and still sturdy unit.

Contents are not included.

WTW Oximeter & pH Meters

Skylarc Ref Q161184

WTW Oximeter & pH Meters.
Includes pH 323, Oci 323, and pH 330i meter units.
See photos for Probes and accessories included.
Condition varies with each meter.

3-Phase 32A Power Extension Cable Lead, 15-Metres

Skylarc Ref X161165

3-Phase 32A Power Extension Cable Lead.
15-Metres length.
Female plug is missing cover cap.

20x 12mm Diameter Steel Rod

Skylarc Ref T161161

20x 12mm Diameter Steel Rod.
Lengths vary from approx 4000mm to approx 4500mm.
Rusty from long term storage

Avery 1766 Benchtop Digital Scale

Skylarc Ref K161152

Avery 1766 Benchtop Digital Scale.
20kg max capacity.
Weighing platform 360x310mm.
Dirty exterior but is functioning normally.

2x Vintage 300mm Engineering Bubble Levels

Skylarc Ref Q160794

2x Vintage 300mm Engineering Bubble Levels.
One Moore & Wright branded unit, model number unknown.
Second unit is a J. Rabone & Sons branded unit.
Both have wooden cases.

Vintage 3-Phase Bandsaw

Skylarc Ref H160941

Vintage 3-Phase Bandsaw.
Unknown manufacturer and model.
3-phase 600V, 32A plug.
Wooden blade cover doors.
820mm diameter blade wheels.
Unable to verify blade size though there is a hand written note on unit stating "16 2½" Blade", see photo.
Cutting Table 710x610mm.
Unknown if saw is functional.

Mitutoyo Disk Micrometers, 3x Units

Skylarc Ref D160781

Mitutoyo Disk Micrometers, 3x Units.
Includes the following code numbers:
- 123-101, 0-25mm.
- 123-126, 1" to 2"
- 123-125, 0" to 1"

Metric unit includes plastic case, Imperial units include wood cases.

2x Laip BT40 Type Tool Holders

Skylarc Ref U160720

2x Laip BT40 Type Tool Holders.
Both are type No. 1112120204
See photos for further type/design details.

4-Leg Lifting Cable Assembly, 1500kg Max Capacity

Skylarc Ref U161188

4-Leg Lifting Cable Assembly.
1500kg Max Capacity.
1.25m cable lengths.
9mm cable diameter.
Master link 150x105mm
Certification expired 2017.

4-Leg Lifting Cable Assembly, 1500kg Max Capacity

Skylarc Ref T161187

4-Leg Lifting Cable Assembly.
1500kg Max Capacity.
1.25m cable lengths.
9mm cable diameter.
Master link 150x105mm
Certification expired 2017.

PAV Electronics 240mm Digital Vernier Calipers

Skylarc Ref U160798

PAV Electronics 240mm Digital Vernier Calipers.
Unknown model number.
Includes wooden case.

Large Assortment of Drill Bits

Skylarc Ref E161094

Large Assortment of Drill Bits

Large Assortment of Drill Bits

Skylarc Ref D161093

Large Assortment of Drill Bits

Large Assortment of Drilling Taps

Skylarc Ref C161092

Large Assortment of Taps

Specialized Single Phase Press

Skylarc Ref S159938

Custom made flywheel press
Single phase
Foot operated
On heavy duty stand

Handy Pneumatic Press

Skylarc Ref R159937

Handy KEC 71 pneumatic press
Cast iron stand
Foot operated

Assorted HSS Bits

Skylarc Ref B161091

Assortment of HSS Bits

Assorted Drill Bits and Tooling

Skylarc Ref A161090

Assorted Drill Bits and Tooling

Test Rite Drill Press

Skylarc Ref H159927

Test Rite Model 00021U
5 speed drill press
Belt drive
200mm x 200mm table
900 - 3200 rpm
1/3 HP motor
Single phase

Mercer Dial Gauges, 3x Units

Skylarc Ref C160780

Mercer Dial Gauges.
Unknown model numbers.
55mm diameter faces.
All operate but not tested for accuracy.

Mitutoyo Vintage 1-2" Micrometer 102-122

Skylarc Ref B160779

Mitutoyo Vintage 1-2" Micrometer.
Code No.102-122
Made in Japan.
Older unit in stylish classic case with purple velvet interior.

Mitutoyo Micrometers, 2x Units

Skylarc Ref Y160776

Mitutoyo Micrometers.
Code numbers are unknown.
One is marked as 1" to 2" and the second is marked as 25-50mm.
Vintage metal cases

Linisher/Grinder on Steel Bench

Skylarc Ref A159920

Single phase linisher
1220mm x 405mm x 820mm tall steel table

Large Assortment of Old Tool Inserts

Skylarc Ref X161087

Large Assortment of Lathe Tool Inserts.
See photos for more details

Box of Left Handed Drill Bits

Skylarc Ref V161085

Box of Left Handed Drill Bits

Cabinet of Drill Bits

Skylarc Ref X159917

11 drawer cabinet
Huge volume of assorted drill bits

Left Handed Drill Bits

Skylarc Ref U161084

Left Handed Drill Bits
See photos for more details

Assorted Reamers

Skylarc Ref T161083

Assorted Reamers

2, 3, 4 Morse Taper Drill Bits

Skylarc Ref S161082

2 3 4 Morse Taper Size Drill Bits

Size 2 and 3 Morse Taper and other Drill Bits

Skylarc Ref R161081

Size 2 and 3 Morse Taper and other Drill Bits

3x Assorted Dial Calipers & Roughness Gauges

Skylarc Ref O160766

3x Assorted Dial Calipers & Roughness Gauges.
Includes:
- Robert Mercin 3 Roughness Instrument.
- Sintokogio Green Hardness Dial Indicator.
- MPJ Dial Caliper, unknown model. (missing glass Dial cover).

All items operate but not tested for accuracy. MPJ Caliper has no case.

Welding Table with Rotator and Stand

Skylarc Ref J159903

Welding table
610mm x 615mm x 860mm tall
160mm three jaw chuck
Single phase with foot control
Small table
690mm x 450mm x 650mm tall

Vice on Workbench

Skylarc Ref H159901

640mm x 700mm x 800mm tall table
Steel frame and wooden top
Carters No.5 130mm vice

Horstmann Thread Gauges M3-M36

Skylarc Ref Q161080

HorstmannThread Gauges M3-M36

2x 3-Point Internal Micrometers

Skylarc Ref L160763

2x 3-Point Internal Micrometers.
Includes:
- Bowers 37-51mm Micrometer w/ 43.998mm ring.
- Fowler - Bowers 5/8" to 3/4" Micrometer, steel ring unit is missing.

One case has detached cover.

Assortment of Compression Springs

Skylarc Ref P161079

Assortment of Compression Springs

7 drawer Workshop Cabinet with Contents

Skylarc Ref K161074

7 Drawer Filing Cabinet with Contents,
Contents include Drill Collets, Spare thread rods and other assorted items.
see photos for more details

7 drawer Workshop Cabinet with Contents

Skylarc Ref J161073

7 Drawer Filing Cabinet with Contents, Omega drawer is missing and 2 drawers don't have handles
Contents include Drill Collets, Spare thread rods and other assorted items.
see photos for more details

Vintage Olivo Water Percentage Meter Assembly

Skylarc Ref E160756

Vintqge Olivo Water Percentage Meter Assembly.
Unsure model.
See photos for included components.

Vintage Electro Forming & Adjusting Tool by Chambrian Eng. LTD

Skylarc Ref D160755

Vintage Electro Forming & Adjusting Tool set.
Ref No. 137B/N142
Made in New Plymouth New Zealand by The Cambrian Engineering Co. LTD.
Age unknown.
Wood case.

7 drawer Workshop Cabinet with Contents

Skylarc Ref H161071

7 Drawer Filing Cabinet with Contents,
Contents include Drill Collets, Spare thread rods, Morse Taper Drill, Drill Bits and other associated items.
see photos for more details

Mitutoyo Gage Block Set 516-903, Incomplete

Skylarc Ref C160754

Mitutoyo Gage Block Set.
Code No.516-903, Set No. BE1-81A
Wood case.
Some blocks are missing, see photos

7 drawer Workshop Cabinet with Contents

Skylarc Ref G161070

7 Drawer Filing Cabinet with Contents,
see photos for more details

Load Easer Forklift Drum Rotator

Skylarc Ref Z160881

Model: Load Easer FLDR
350kg capacity

Welding Bench with Vice

Skylarc Ref V160877

860mm x 1200mm x 870mm tall steel table
5mm plate steel top
Toolshed 150mm vice

Brass Sleeves

Skylarc Ref A161064

Brass Sleeves in 2 wooden boxes, thicknesses and lengths vary, see photos for more details

Small Cabinet with Lathe Tooling

Skylarc Ref Z161063

Small Cabinet with Lathe Tooling

3 x BT40 Tool Holders

Skylarc Ref X161061

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref W161060

3 x BT40 Tool Holders

Herbert Drill Press

Skylarc Ref N160869

Vintage Herbert pedestal drill press
Three speeds 2000/3500/5600rpm
80mm spindle travel
Three phase
305mm x 280mm table

3 x BT40 Tool Holders

Skylarc Ref V161059

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref U161058

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref T161057

3 x BT40 Tool Holders

GMF Bench Grinder w/ Stand

Skylarc Ref N160739

GMF Bench Grinder w/ Stand.
Uses disks up to 180mm diameter.
Single Phase.
Includes 840mm tall heavy Steel stand.
Older unit showing heavy usage. Eye safety guard screens are missing.

GMF Bench Grinder w/ Stand

Skylarc Ref M160738

GMF Bench Grinder w/ Stand.
Uses disks up to 150mm diameter.
Single Phase.
Mounted on a 900mm tall heavy Steel Stand.
Shows heavy usage.
Eye safety screens are intact.

3 x BT40 Tool Holders

Skylarc Ref S161056

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref R161055

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref Q161054

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref P161053

3 x BT40 Tool Holders

CNC Machine Vice

Skylarc Ref K160736

CNC Machine Vice.
Unknown manufacturer.
140mm wide jaws.
Opens to approx 105mm
Mounting bolt slots spaced approx 350mm and150mm appart on centre.
Crank handle is missing

CNC Machine Vice

Skylarc Ref J160735

CNC Machine Vice.
Unknown manufacturer.
Made in Japan.
140mm wide jaws.
Opens to approx 105mm
Mounting bolt slots spaced approx 350mm and150mm appart on centre.
Crank handle is included.

3 x BT40 Tool Holders

Skylarc Ref O161052

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref N161051

3 x BT40 Tool Holders

Two Grinders Mounted on Trolley

Skylarc Ref I160864

Steel frame and wooden top
GMF 200mm bench grinder
6" bench grinder
Both single phase

CNC Machine Vice

Skylarc Ref I160734

CNC Machine Vice.
Unknown manufacturer.
150mm wide jaws.
Opens to approx 110mm.
Swivel base with mounting bolt slots spaced approx 200mm appart on centre.
Total length approx 440mm.
Crank handle is missing

3 x BT40 Tool Holders

Skylarc Ref M161050

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref L161049

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref K161048

3 x BT40 Tool Holders

CNC Machine Vice

Skylarc Ref G160732

CNC Machine Vice.
Unknown manufacturer.
160mm Jaw width.
Opens to approx 145mm.
410mm Vice length.
Side mounting bolt slots spaced approx 180mm appart on centre.
Includes crank handle attachment.
Shipping is not available due to it being over max weight limit of our courier.

3 x BT40 Tool Holders

Skylarc Ref J161047

3 x BT40 Tool Holders

CNC Machine Vice

Skylarc Ref F160731

CNC Machine Vice.
Unknown manufacturer.
160mm Jaw width.
Opens to approx 145mm.
410mm Vice length.
Side mounting bolt slots spaced approx 180mm appart on centre.
Includes crank handle attachment.
Shipping is not available due to it being over max weight limit of our courier.

CNC Machine Vice

Skylarc Ref E160730

CNC Machine Vice.
Auto Well branded.
160mm Jaw width.
Opens to approx 145mm.
410mm Vice length.
Side mounting bolt slots spaced approx 180mm appart on centre.
Includes crank handle attachment.
Shipping is not available due to it being over max weight limit of our courier.

3 x BT40 Tool Holders

Skylarc Ref I161046

3 x BT40 Tool Holders

Shelf and Contents of Industrial Supplies

Skylarc Ref B160857

Galvanized shelving
Contents include
Electric motors and parts
Electrical fittings
Air fittings
Bolts and nuts
All in unknown condition
Buyer will need to unload the shelves themselves

3 x BT40 Tool Holders

Skylarc Ref H161045

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref G161044

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref F161043

3 x BT40 Tool Holders

6x BT40 Type ER Collet Chuck Tool Holders

Skylarc Ref C160728

6x BT40 Type ER Collet Chuck Tool Holders.
Includes:
- Unknown brand, type 40 ER32x100
- Illegible markings, BT40 ER32x120mm size (hand measured(.
- illegible markings, BT40 ER24x120mm size (hand measured).
- Unknown brand, type 40 ER32x100 E.
- Kennametal brand, type number illegible, hand measured as ER24x100.
- Kennametal brand, type number illegible, hand measured as ER32x70

6x BT40 Type ER Collet Chuck Tool Holders

Skylarc Ref B160727

6x BT40 Type ER Collet Chuck Tool Holders.

- Kojex type BT40 ER32-60
- 2x of same design, illegible ID marks hand measured to ER32x60
- Sandvik Coromant brand, type marking illegible, hand measured to ER40x60
- 2x unknown brand, both marked as type 40 ER40x80 E

3 x BT40 Tool Holders

Skylarc Ref E161042

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref B161039

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref A161038

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref Z161037

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref Y161036

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref X161035

3 x BT40 Tool Holders

6x BT40 Type ER Collet Chuck Drill Tool Holders

Skylarc Ref A160726

6x BT40 Type ER Collet Chuck Drill Tool Holders.
Includes:
- 4x Kojex BT40-ER32-60
- 1x Kennametal BT40 ER32070M
- 1x Tool Holder with illegible markings though of same dimensions as Kennametal holder.

Condition varies with each unit.

3 x BT40 Tool Holders

Skylarc Ref W161034

3 x BT40 Tool Holders

6x BT40 Type ER32 Collet Chuck Drill Tool Holders by Kojex

Skylarc Ref Z160725

6x BT40 Type ER32 Collet Chuck Drill Tool Holders.
All are Kojex type BT40-ER32-60
Condition varies with each unit.

6x BT40 Type ER Collet Chuck Drill Tool Holders

Skylarc Ref Y160724

6x BT40 Type ER Collet Chuck Drill Tool Holders.
2x units are Kennametal type BT40-ER32070M, the remaining 4x units have illegible markings but are of the same dimensions and Collet size as the known Kennametal units.
Condition varies with each unit.

3 x BT40 Tool Holders

Skylarc Ref V161033

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref U161032

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref T161031

3 x BT40 Tool Holders

6x BT40 Type ER Collet Chuck Drill Tool Holders

Skylarc Ref X160723

6x BT40 Type ER Collet Chuck Drill Tool Holders.
Includes:
- 1x Sandvik Coromant ER40 holder Type 392.5515-40 25 080.
- 3x Unknown brand with ID markings of 40 ER32x100 E.
- 1x illegible markings unit with ER32 Chuck and approx 60mm length.
- 1x illegible markings unit with ER24 Chuck and approx 60mm length.

Condition varies greatly with each unit.

6x BT40 Type ER Collet Chuck Drill Tool Holders

Skylarc Ref W160722

6x BT40 Type ER Collet Chuck Drill Tool Holders.
Includes:
- Kennametal type BT40 ER32070M
- 2x Sandvik Coromant units both with illegible type markings, one appears to be an ER40 Chuck with approx 80mm length and the second is possibly an ER50 with approx 90mm length.
- 1x Laip brand type 0412060208, appears to be a ER50 size with approx 90mm length.
- 2x remaining units have no legible ID markings, one is an ER32 and the second an ER40.

Condition varies with each unit.

3 x BT40 Tool Holders

Skylarc Ref S161030

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref R161029

3 x BT40 Tool Holders

2x BT40 Holders w/ Keyless 13mm Drill Chucks by Vertex

Skylarc Ref V160721

2x BT40 Holders w/ Keyless 13mm Drill Chucks by Vertex.
Both are type No. BT40-APU-13
Chuck Jaws move smoothly on both units.

3 x BT40 Tool Holders

Skylarc Ref Q161028

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref P161027

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref O161026

3 x BT40 Tool Holders

Hitachi Impact Drill

Skylarc Ref P160585

Model: Hitachi RHB DV 20VD
20mm impact drill
2 speed ranges 0-1100/0-3000 rpm
860 watt
I'm case

3x BT40 Tool Holders w/ Indexable Milling Cutters

Skylarc Ref T160719

3x BT40 Tool Holders w/ Indexable Milling Cutters.
Includes:
- Tecnara Tool Holder type No.240-212-2 with an attached Valenite VAL-U-MILL cutter VMM-91-4-12510RA, 125mm Diameter.
- Unknown brand BT40 Holder with a Kennmetal 100mm diameter Cutter type No. 100B07RK.
- Unknown brand BT40 Holder with unknown brand/model indexable cutter approx 75mm diameter.

Condition varies with each unit.

Hitachi Sabre Saw

Skylarc Ref O160584

Hitachi CR 13VB reciprocation saw
1050 watt
0-2800/min
Case
Blades

3 x BT40 Tool Holders

Skylarc Ref N161025

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref M161024

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref L161023

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref K161022

3 x BT40 Tool Holders

4x BT40 Type Straight Shank Drill / Tool Holders

Skylarc Ref S160718

4x BT40 Type Straight Shank Drill / Tool Holders.
Includes:
- AW branded holder type No.BT40-SLA42-105
- Unknown brand holder type No. 40 EM25x105 E
- Sandvik Coromant branded holder 392.5220-40 20 090
- Illegible markings holder with approx 105mm length and 32mm inner hole diameter.

Condition varies with each unit

3 x BT40 Tool Holders

Skylarc Ref J161021

3 x BT40 Tool Holders

8 x BT30 Tool Holders and Holding Rack

Skylarc Ref I161020

8 x BT30 Tool Holders and Holding Rack

4x BT40 Type Tool Holders w/ Milling Cutters

Skylarc Ref R160717

4x BT40 Type Tool Holders w/ Milling Cutters.
Includes:
- Kojex type BT40-FMC22-105 with Speedmax Walter branded Cutter type ISSF 100-10-MP,.
- Kennamwtal holder, type ID illegible, measures approx 100mm long, 50mm diameter and has Sandvik Coromant Cutter R390-063022-17M
- Unknown brand holder type No. 40 SM22x60 E with unknown brand Cutter type No. PACM2050HR.
- Unknown brand holder type No. BT40 SEM 22x60 E with Sandvik Coromant clutter type No. R390-050Q22-17H

6 x BT30 Tool Holders and Holding Rack

Skylarc Ref H161019

6 x BT30 Tool Holders and Holding Rack

6x Assorted BT40 Tool Holders

Skylarc Ref Q160716

6x Assorted BT40 Tool Holders.
Includes:
- Nikken type No. BT40-SCA27-75
- Kojex type No. BT40-ER32-60
- Graflex type No. FM4041 101 1490 with unknown brand boring attachment type No. A780 20, 30-40 1.180-1.575
- Illegible ID markings holder with large 140mm long, 48mm diameter boring bar attachment, also unknown brand/ID number.
- Unknown own brand/ type BT40 Holder with 60mm diameter attachment mount.

Condition varies wirh each unit.

Assorted Tooling for BT Tool Holders

Skylarc Ref G161018

Assorted Tooling for BT Tool Holders

Nikken BT40 Micro Touch Edge Detector UMT200

Skylarc Ref P160715

Nikken BT40 Micro Touch Edge Detector UMT200.
Untested as batteries are depleted

Milling Machine Manual Indexing Head

Skylarc Ref D160573

160mm chuck
Turns freely and locks
One side of mounts broken

3x BT40 Tool Holders w/ Indexable Mill Cutters

Skylarc Ref O160714

3x BT40 Tool Holders w/ Indexable Mill Cutters.
Includes:
- AW holder type No. BT40 FMB27-150 with Kennametal Cutter type 80A06RK.
- Unknown brand/type BT40 Holder with 220mm long, 45mm diameter attachment that has an unknown brand/model 50mm diamter Cutter attached.
- Unknown brand/type BT40 Cutter with 110mm long, 40mm diameter shank with a Kennametal type MS-1184, 50A04RS90TP16D indexable Cutter.

Condition varies with each unit

4x Assorted BT40 Type Tool Holders

Skylarc Ref N160713

4x Assorted BT40 Type Tool Holders.
Includes:
- Unknown brand/model BT40 Holder with 13mm Keyless Albrecht branded drill Chuck.
- Sandvik Coromant Holder type C4-390.55-40 030 with Sandvik Coromant boring attachment C4-391.38A-1-033 106 A
- Sandvik Coromant Holder type C3-390.55-40 030 with Sandvik Coromant boring attachment C3-391.38A-1-024 086 A.
- Nachi Holder type SF BT40-BCA 19-120

Condition varies with each unit.

5x Assorted BT40 Type Tool Holders

Skylarc Ref M160712

5x Assorted BT40 Type Tool Holders.
Includes:
- Sandvik Coromant Holder type 392.5520 20 32 100 with 240mm long modified 25mm diameter Cutter.
- 2x ER32 type Holders of unknown brand/model numbers with lengths of approx 100mm and 60mm.
- 2x straight shank bit Holders of unknoen brand/model, one approx 90mm long excluding attachment and the other approx 105mm long excluding attachment.

Condition varies with each unit.

Assortment of ER Collets

Skylarc Ref C161014

Assortment of Collets
See photos for more details

Nikken NT40 or Similar Quick Change Morse Taper Tool Holder Set

Skylarc Ref J160709

Nikken NT40 or Similar Quick Change Morse Taper Tool Holder Set.
Made in Japan by Nikken.
Main quick change Chuck Tool Holders is marked NQ40-35.
Includes 6x quick change inserts, 3x are for Morse Taper No.3 Shanks and 3x are for Morse Taper No. 2 shanks.
Ball Bearings on all units spin smoothly.

Assortment of Drill Bits

Skylarc Ref A161012

Assortment of Drill Bits

Assorted Drill Bits and Accessories

Skylarc Ref X161009

Assorted Drill Bits and Accessories.

15 Drawer Cabinet and Contents

Skylarc Ref H160551

Steel workshop cabinet
Contents of modified taper shank drills
Dial gauge and magnetic base components

Mitutoyo Combination Set CMST2-12C

Skylarc Ref V161397

This is a Mitutoyo CMST2-12C combination square set, including a square head, center head, and protractor head. The blade is marked and hardened, indicating grade C precision. Comes in original packaging with protective foam insert.

45x Assorted End Mill Bits, Cutters, Drills

Skylarc Ref L160997

45x Assorted End Mill Bits, Cutters, Drills.
Various brands and types.
Mounting shank diameters range from 5mm to 25mm.
Condition varies greatly with each unit.

24x Assorted Ripper & Finishing End Mill Cutters

Skylarc Ref K160996

24x Assorted Ripper & Finishing End Mill Cutters.
Mounting shanks range from 10mm to 32mm.
See photos for details on types included.
Condition varies greatly with each unit.

Antique Wooden Workbench w/ Vice

Skylarc Ref H160993

Antique Wooden Workbench w/ Vice.
70mm thick wood board top.
142x68mm thick wood legs and frame.
Includes unknown brand vintage double Jaw vice approx 350x190x265mm.
Vice is not attached to Workbench.
Age of items is unknown.
Workbench very old but still a solid unit. Vice still operates.

The Tool Shed Corded Die Grinder TSDG1

Skylarc Ref D160989

The Tool Shed Corded Die Grinder.
Model No. TSDG1
750W

Workshop Cabinet and Contents

Skylarc Ref S161394

Workshop Cabinet and Contents

Antique Wood Wookbench w/ Vice

Skylarc Ref C160988

Antique Wood Wookbench w/ Vice.
65mm thick wood board top.
Carter Semi Steel No. 5 vice attached.
Age of Workbench unknown .
Shows very heavy wear and usage with top surface worn down to approx 30mm thick in the front centre of Workbench.

Workshop Trolley

Skylarc Ref R161393

Workshop Trolley.
Angle steel frame, plywood top.

9x 2-piece Mill Cutters

Skylarc Ref B160987

9x 2-piece Mill Cutters.
Diameters from approx 92mm to 100mm.
Most are Walter Spencer & Co. brand.
Various teeth designs
All split into two halves, see photos.

Vintage Tanner Single Phase Drill Press w/ Trolley

Skylarc Ref Z160985

Vintage Tanner Single Phase Drill Press.
Unknown model number.
Drill Press approx 950mm tall.
Drill bed approx 340x255mm.
13mm Keyed Chuck, key is missing.
Includes 760mm tall Trolley Cart the drill is on.

Some Type of Standy Thing

Skylarc Ref P161391

Some kind of Standy Thing 800mm wide at base, stands on three legs, has an adjustable shaft that extends to 300mm height.
Holder is 110mm box V shape with two screws to hold down that extend 180mm

Mitutoyo Vernier Caliper, Modified Extended Length

Skylarc Ref P160975

Mitutoyo Vernier Caliper, Modified Extended Length.
Unknown model number.
Originally a 300mm Caliper that has been carefully cut and lengthen to a measuring length of approx 750mm.
Total extended Tool length approx 840mm.
Accuracy of tool is unknown.
Some surface rust spotting

Wild Heerbrugg M5A Stereo Microscope w/ PSU Unit

Skylarc Ref O160974

Wild Heerbrugg M5A Stereo Microscope.
Made in Switzerland.
Measures approx 200mm Diameter and 445mm tall.
Note that it's non-New Zealand compliant European plugs have been removed, buyer is responsible for replacing plugs and any potential hazards associated.
Lighting has not been tested.
Also includes Wild Heerbrugg Lamp.Illuminator Power Supply unit Type No. MTR28

Record No. 35 Benchtop Vice

Skylarc Ref J160969

Record No. 35 Benchtop Vice.
Made in England
135mm wide jaws.
Opens to approx 155mm.
490x190x210mm overall size.

Industrial Forge Crucible Trolley

Skylarc Ref E160964

Industrial Forge Crucible Trolley.
360mm diameter tyres.
Rotating centre shaft for pouring Crucible molten contents.
Crucible approx 400mm diameter and 430mm tall.
See photos for details on Crucible condition. Unknown if Crucible is intact.

Industrial Forge Crucible Trolley

Skylarc Ref D160963

Industrial Forge Crucible Trolley.
400mm diameter tyres.
Rotating centre shaft for pouring Crucible molten contents.
Crucible approx 330mm diameter and 440mm tall.
See photos for details on Crucible condition.

Industrial Forge Crucible Trolley

Skylarc Ref A160960

Industrial Forge Crucible Trolley.
400mm diameter tyres.
Rotating centre shaft for pouring Crucible molten contents.
Crucible approx 420mm diameter and 400mm tall.
See photos for details on Crucible condition. Unknown if Crucible is intact.

Assorted Angle Grinder Metal Cutting Grinding Disks

Skylarc Ref P160949

Assorted Angle Grinder Metal Cutting Grinding Disks.
Diameters include 125mm, 180mm, 230mm.
Most are new unused, see photos for brands and types and amounts included of each.
There is also included some used disks.

Flex Corded Straight Grinder H1206

Skylarc Ref N160947

Flex Corded Straight Grinder.
Model No. H1206
1600W
Previously used in a foundry setting.

Flex Corded Straight Grinder H1206

Skylarc Ref M160946

Flex Corded Straight Grinder.
Model No. H1206
1600W
Previously used in a foundry setting.

Contents of Shelving

Skylarc Ref L160529

This Auction is for the Contents of the Shelving.

SHELVING NOT INCLUDED.

Contents of Shelving

Skylarc Ref K160528

This Auction is for the Contents of the Shelving.
Buyer will need to unload the shelving themselves
SHELVING NOT INCLUDED.

Contents of Shelving

Skylarc Ref J160527

This Auction is for the Contents of the Shelving.
Buyer will need to unload the shelving themselves
SHELVING NOT INCLUDED.

Contents of Shelving

Skylarc Ref I160526

This Auction is for the Contents of the Shelving.
Buyer will need to unload the shelving themselves
SHELVING NOT INCLUDED.

Contents of Shelving

Skylarc Ref H160525

This Auction is for the Contents of the Shelving.
Buyer will need to unload the shelving themselves
SHELVING NOT INCLUDED.

Contents of Shelving

Skylarc Ref G160524

This Auction is for the Contents of the Shelving.
Buyer will need to unload the shelving themselves
SHELVING NOT INCLUDED.

Handheld Furnace Temperature Indicator

Skylarc Ref H161383

WLX brand
Model: PE94
Manufactured 2019
Includes manual
Charger
Large number of probe covers
Box

Contents of Shelving

Skylarc Ref F160523

This Auction is for the Contents of the Shelving.
Buyer will need to unload the shelving themselves
SHELVING NOT INCLUDED.

Contents of Shelving

Skylarc Ref E160522

This Auction is for the Contents of the Shelving.
Buyer will need to unload the shelving themselves
SHELVING NOT INCLUDED.

Contents of Shelving

Skylarc Ref D160521

This Auction is for the Contents of the Shelving.
Buyer will need to unload the shelving themselves
SHELVING NOT INCLUDED.

Contents of Shelving

Skylarc Ref C160520

This Auction is for the Contents of the Shelving.
Buyer will need to unload the shelving themselves
SHELVING NOT INCLUDED.

Assorted Foundry Melt Ingredients, Additives + Shelf

Skylarc Ref B160935

Assorted Foundry Melt Ingredients, Additives.
Nickel, Iron, Silicon, Aluminium and other types of additives and ingredients for metal melts, see photos.
Includes the green/white shelf unit 1300x450x1810mm.
Leftover Foundry supplies. Some bags/containers are partials, some others are full and unopened

Workshop Trolley and Contents

Skylarc Ref U161370

Heavy duty steel frame
MDF top
Contents include
100mm mill vice
CO2 regulator on hose
Clamps
Large vice

Miller CoolMate 3 Welding Water Cooler, Faulty Plug

Skylarc Ref U160928

Miller CoolMate 3 Welding Water Cooler.
Single Phase plug is damaged, see photos, so unable to test. Functionality of unit is unknown

Pallet of Rubber Mats

Skylarc Ref N161285

Pallet of Rubber Mats
Unkown Amount
Assorted Types
See photos for more details

Paint Cabinet with Paint Supplies

Skylarc Ref O161286

Paint Cabinet and Paint Supplies.
Cabinet included
See photos for more details

7 x Lathe Boring Bars

Skylarc Ref F161355

Assorted boring bars

7 x Lathe Boring Bars

Skylarc Ref E161354

Assorted boring bars

7 x Lathe Boring Bars

Skylarc Ref D161353

Assorted boring bars

3 Phase Rock Tumbler

Skylarc Ref I161280

3 phase Rock Tumbler
Tumbler Barrel is 950mm long and 450mm wide. Also comes with tumbling stones pictured below.

Rock Tumbler

Skylarc Ref H161279

Rock Tumbler
Tumbler Barrel is 550mm wide and 350mm deep.
Appears to have a Gas Line and a burner beneath it.

Vibratory Finishing Machine

Skylarc Ref G161278

Vibratory Finishing Machine
Machine is 1100mm long and 500mm wide. Drum is 700mm x 350mm.

Includes The Trolley and Sluice

Vibratory Finishing Machine

Skylarc Ref F161277

Vibratory Finishing Machine
Machine is 2000mm long and 600mm wide. Drum is 950mm x 430mm.

Rock Tumbler

Skylarc Ref E161276

Rock Tumbler
Tumbler Barrel is 820mm wide and 350mm deep.

Lot of Machine Tool Tips

Skylarc Ref U161318

10 partial boxes
Most look new

4-Leg Lifting Cable Assembly, 2480kg Max Capacity

Skylarc Ref V161189

4-Leg Lifting Cable Assembly.
2480kg Max Capacity.
2.03m cable lengths.
Master link 180x120mm.
8mm diameter cable size.
Last tested in June 2017.

Slack and Parr Mutil Spindle Drill

Skylarc Ref O161312

Model: Slack and Parr Drilling Machine Type M.A.I.
Three phase
420mm x 270mm table
On steel stand
No plug

6x Lathe Turning Tools by Iscar, 25x25mm size

Skylarc Ref P161183

6x Lathe Turning Tools by Iscar
All are 25x25mm size. Length approx 130mm to 135mm.
Includes:
- 1x GHGR 25-3
- 3x GHDR 25-3 (One has a modified tip)
- 2x GHDR 25-4

Condition varies with each tool.

7x Lathe Boring Bars, Assorted Sizes

Skylarc Ref M161180

7x Lathe Boring Bars.
Includes the following brands/types:
- Iscar GHIR 25-25-4, 200mm length
- Unknown brand S25S-SDQCR11, 185mm length
- Ceradex S25X-SVUBR16-34E, 220mm length
- Unknown brand A25R MWLNL-06W, 200mm length
- Iscar S20R SDUCR-11, 200mm length
- Iscar SDUCR-BS-20?? (remaining number is cut off), 145mm length
- Unknown brand CHIR 20-20-4, 125mm length.

Condition varies with each Tool.

23x Assorted Thread Taps

Skylarc Ref C161170

23x Assorted Thread Taps.
Sizes from 6mm to 1 ½" diameters.
Condition varies with each unit.

Meca Turret Drill

Skylarc Ref Y161478

Meca rotary turret drill
Three phase
6 stations
12 spindle speeds
275-4010 rpm
355mm x 300mm T slot table
Pneumatic vice
Draw with contents of chucks and accessories
No plug
Surface corrosion

6-Metre Steel Pipe

Skylarc Ref V161163

6-Metre Steel Pipe
165mm diameter.
Approx 8mm thick.
Rusty from outdoor storage. One end is dented.

3-Phase Electrical Power Extension Cable Lead, 6-Metre Length

Skylarc Ref U161162

3-Phase Electrical Power Extension Cable Lead.
6-Metre Length.
4-pin 500V, 32A male ug to 500V, 16A female plug of smaller diameter and pin spacing, see photos.
Some worn cable casing.

Pile of Aluminium Hinge Component Lengths

Skylarc Ref N161155

Pile of Aluminium Hinge Component Lengths.
Uncut hing compinents, each length approx 3100mm.
Two widths in pile, 23mm and 49mm.
Total number in pile is u known, a rough estimate is around 150 or so.
As new leftover factory parts stock.

Vacuum Pump

Skylarc Ref Y161244

430mm diameter pump
5.5kW three phase motor
Filter housing
Some pipes

Large Assortment of Scrap Metal

Skylarc Ref Z161271

Large Assortment of Scrap Metal

BT40 Tool Holders

Skylarc Ref V161267

BT40 Tool Holders

Assorted BT and NT Tool Holders

Skylarc Ref U161266

Assorted BT and NT Toll Holders

Assorted NT and BT Tool Holders

Skylarc Ref S161264

Assorted NT and BT Tool Holders

BT40 Tool Holders

Skylarc Ref R161263

BT40 Tool Holders

BT40 Tool Holders

Skylarc Ref Q161262

BT40 Tool Holders

Shelving with Contents

Skylarc Ref O161260

Shelving With Contents
Shelving is 240pmm long with 4 shelves at 530mm deep and a total height if 1800mm
Buyer will have to dismantle

SAMSON Rollasava Parts

Skylarc Ref G161252

Samson Rollasava Toilet Roll Holder parts

Pallet of Assorted Fasteners

Skylarc Ref F161251

Pallet of Assorted Fasteners

Contents of Shelving

Skylarc Ref E161250

This Auction is for the Contents of the Shelving.

SHELVING NOT INCLUDED.

Hoppers

Skylarc Ref D161249

main Hopper is 1200mm x 1200mm and is 900mm tall before tapering off. is made of galvanised steel

The frame is 1150mm x 670mm x 160mm and is made from 3 inch box steel with flat plates on the top and bottom

The Gold coloured Hopper is 900mm x 900mm x 750mm and appears to be made of Steel.

Pallet of Scrap Parts

Skylarc Ref U161474

Pallet of Scrap Parts
Mainly Aluminium

Pallet of Hinge Parts

Skylarc Ref T161473

Pallet of Hinge Parts.

Small Swivel Vice

Skylarc Ref R161471

Small Swivel Vice
Jaws are 80mm x 100mm

Assorted Sands

Skylarc Ref Q161470

Assorted Sands

2 x Diff Covers

Skylarc Ref F161225

2 x Diff Covers
Each are 550mm long and 280mm wide
Unknown what these are for.

11x Adjustable Plain Caliper Gauges

Skylarc Ref F160757

11x Adjustable Plain Caliper Gauges.
Ten are Matrix branded a d one is StayPut brand.

Imperial sizes, see photos.

4x Jacobs Chuck Keyed Drill Chucks w/ Morse Taper Shanks

Skylarc Ref I160708

4x Jacobs Chuck Keyed Drill Chucks w/ Morse Taper Shanks.
All are Jacobs Chuck USA brand.
2x are Model 6A, 1/2" (13mm) with Morse Taper No. 2 shanks
2x are Model No. 14, 1/2" (13mm), one with Morse Taper No. 2 and one with No. 3 shank.
All include Chuck keys.
All operate smoothly but not tested under load.

Somta 74mm Diameter Drill Bit w/ No.5 Tapered Shank

Skylarc Ref H160967

Somta 74mm Diameter Drill Bit.
No.5 Tapered mounting Shank
260mm cutting depth.
435mm total length.

Pistol Grip Dial.Gauges, 2x Units

Skylarc Ref W160774

Pistol Grip Dial.Gauges.
Both are made in England by Verdict, specific model numbers are unknown.

6x Assorted G-Clamps

Skylarc Ref L160737

6x Assorted G-Clamps.
Two Record No. 120, 12" Clamps.
One Dawn branded 12" Clamp.
Two unbranded approx 200mm Clamps.
One custom made approx 220mm Clamp.
Condition varies with each unit. The Record and Dawn branded Clamps are missing threaded rod cap blocks, see photos. One Record Clamp has bent threaded rod.

7x Assorted BT40 & CAT40 Tool Holders

Skylarc Ref L160711

7x Assorted BT40 & NT40 Tool Holders.
Appear to be older units with Assorted attachments on some, see photos for further details.

Assorted CNC Lockdown Parts & Components

Skylarc Ref D160703

Assorted CNC Lockdown Parts & Components.
Triangle blocks up to 140x85x40mm size.
Threaded rod diameters of 12mm and 15mm.
Assorted other related components, see photos.
Condition varies with each item.

16x Assorted Mill Cutters

Skylarc Ref M160998

16x Assorted Mill Cutters.
Diameters from approx 75mm to 140mm.
See photos for type details.
Most have very dirty or rusty surfaces so unable to read ID markings.
Condition varies with each unit

Makita Corded 125mm Angle Grinder GA5040C

Skylarc Ref F160991

Makita Corded 125mm Angle Grinder.
Model No. GA5040C.
Includes side handle and disk guard.
Disk changing tool is missing.

6x Assorted Telescoping Gauges by Mitutoyo and Moore & Wright

Skylarc Ref V160981

6x Assorted Telescoping Gauges by Mitutoyo and Moore & Wright.
Includes:
- 5x Mitutoyo telescoping gauges sizes AA, A, C, D, and E
- Vintage Moore & Wright wooden gauge set case with one No.900 model 31.7-53.9mm gauge still included.

Mitutoyo Micrometers & Dial Gauge

Skylarc Ref S160978

Mitutoyo Micrometers & Dial Gauge.
Includes:
- Dial test indicator model 513-104 (no case)
- 0-25mm Micrometer with case, model number unknown.
- 0-1" Micrometer with case, model number unknown.

Benchtop Guillotine Shears

Skylarc Ref J160943

Benchtop Guillotine Shears.
Unknown manufacturer/model.
Main body 360mm long, 300mm tall with 200mm long lower Jaw, 225mm upper Jaw.

Avery Vintage 210kg Mechanical Scale

Skylarc Ref E160938

Avery Vintage 210kg Mechanical Scale.
Type No. 390/AAG
210kg max capacity.
Weighing platform 620x400mm and 185mm above floor.
Includes 2x loose weight attachments, see photos.
Older model. Weighing platform seems to float smoothly on its support. We assume there is supposed to be more than 2x loose weights so likely there are some missing. Some surface rust on scale.

Workshop Mobile Shelf Trolley w/ 2x Attached Bench Grinders

Skylarc Ref Y160932

Workshop Mobile Shelf Trolley w/ 2x Attached Bench Grinders.
Angle steel Trolley frame with wood board shelves and heavy Duty castors.
Includes GMF 200mm bench grinder with one missing side guard and one damaged eye screen guard. Second side guard is detached but included.
Includes unknown brand bench grinder RBG 150A using 150mm diameter brush disks. This grinder is missing almost all Guards, see photos.

Vintage Bates Model C Self-Making Staple Stapler w/ Refills

Skylarc Ref X160905

Vintage Bates Model C Self-Making Staple Stapler w/ Refills.
Age unknown.
Made in USA.
Stapler measures approx 200x60x110mm.
Stapler operates normally and cuts and forms its own staples from a spool of brass wire. Makes a staple approx 8mm long.
Auction also includes 98x Bates B-50 brass wire refill assemblies in their original bulk packaging boxes.
Condition- Stapler shows usage and wear from years of use but still operates normally. The Refills are as new unused though their boxes show fading and dust from decades of storage

Assorted Office Furniture

Skylarc Ref T160901

Assorted Office Furniture.
Includes:
- Grey Corner Desk 1800x1800x735mm.
- Faux wood Corner Desk with adjustable Height feet (currently on its side) 1800x1800x750mm.
- Grey 3-drawr unit 550x475x620mm.
- Faux Wood Shelf 900x310x1800mm.

Auction ONLY includes the above four items, all other items seen on and nearby are NOT included!
Condition varies with eaxh item.

6x Assorted Lathe Boring Bars, 16mm diameter size

Skylarc Ref N161181

6x Assorted Lathe Boring Bars.
All are 16mm diameter size.
Includes the following:
- 3x Iscar S16Q SDUCR-07, 180mm lengths
- 2x Iscar GEHIR 16-16-2, 160mm lengths
- 1x Unknown brand, type R166.4KF-16F16, 130mm length.

Condition varies with each tool.

5x Assorted Indexable Mill Drills

Skylarc Ref H161175

5x Assorted Indexable Mill Drills.
Includes:
- Iscar DZ030-090-32-05, 31mm diameter cut, 90mm depth.
- Unknown brand NPD 250-32-3, 25mm cut diameter, 80mm cut depth.
- Unknown brand/type 30mm diameter, 90mm deep cut.
- Unknown brand/type 25mm diameter, 80mm depth cut.
- Unknown brand/type 22mm diameter, 75mm deep cut.

Condition varies with each unit.

7x Assorted Indexable Mill Drills

Skylarc Ref G161174

7x Assorted Indexable Mill Drills.
Includes:
- Iscar DCM 120-060-16A
- Iscar DCM 120-036-16A
- Iscar DCM 120-060-16A-5D
- Iscar DCM 110-055-16A-5D
- Sandvik Coromant R416.2-0140L20-31
- Sandvik Coromant R416.2-0160L20-31
- Unknown brand/type with 12.7mm diameter, 40mm deep cut.

Condition varies with each unit.

6x Assorted Indexable Mill Cutters

Skylarc Ref F161173

6x Assorted Indexable Mill Cutters.
Includes:
- Iscar Heli2000 HM90 E90A-D32-4-W25
- Iscar Heli2000 HM90 E90A-D16-2-C16
- Kennametal 5E2R038K25SRD10
- 3x other Cutters with no legible markings, two with approx 12mm diameter shank and one with 20mm diameter shank

Condition varies with each unit.

Office Front Reception Counter Assembly

Skylarc Ref X161139

Office Front Reception Counter Assembly.
Wood board trim and customer side counter top.
Dark Grey laminate receptionist counter top..
Painted MDF body.
Curved design.
Rear counter 720mm high.
Items seen on and around counter are not included

Assorted Spliting Mill Cutters

Skylarc Ref N160999

Assorted Spliting Mill Cutters.
All components are approx 95mm diameter with 25mm diameter centre mounting hole.
Two Cutters are complete with matching halves, a third is two non matching halves stuck together and the remaining six do not have teeth that match up with other units.
See photos for further type/ design details.
Condition varies with each unit

Workshop Heavy Duty Mobile Shelf Trolley

Skylarc Ref I160942

Workshop Heavy Duty Mobile Shelf Trolley.
Angle steel frame with wood board shelves.
Large heavy Duty 200mm Diameter, 60mm wide castor wheels.
Total length and width of Trolley including the large wheel Mounts is approx 885x550mm.
Well used but very sturdy unit.

Workshop Shelving and Contents

Skylarc Ref W159942

Metal shelving
Contents include
2 x small hand presses
Bins of nuts and bolts
Empty tool cases
Grease gun

Vintage Mercer 155 + Adjustable Power Supply

Skylarc Ref J160787

Vintage Mercer 155 + Adjustable Power Supply.
Includes:
- Mercer model 155 probe assembly with gauge meter unit, dial control unit and 250mm long Clamp mount unit, see photos.
- Adjustable power supply unit model EA-3050 by Regelbares Netzgerat.

Both older units are well used and both need new power cord plugs. Both are untested.

Vintage J. Rabone & Sons Hardwood & Brass 685mm Bubble Level

Skylarc Ref G160784

Vintage J. Rabone & Sons Hardwood & Brass 685mm Bubble Level.
Made in England.
Both bubble Vials are intact.
Age unknown.
Hardwood with brass Fittings and end caps.
Approx 685x80x32mm

Steel Shelving and Contents

Skylarc Ref L159931

Metal shelving unit
Contents include
Press plates
Drill accessories
Small hotplate
Various industrial supplies

Trolley and Contents

Skylarc Ref K159930

4 level trolley
Mesh shelves
Contents include
Collets
Tools
Various industrial supplies

Multihead Drill Press

Skylarc Ref C159922

6 linked drilling heads
On steel stand
Possibly for doweling or similar
Three phase

Large Lot of Reamers

Skylarc Ref W159916

Approx 65 assorted reamers
Largest 28mm

Assorted Tooling

Skylarc Ref V159915

Approx 70 assorted machine tools
End mills
Bull nose cutters
Assorted others
Metric and imperial

5 x Pneumatic Vices

Skylarc Ref T159913

Small air operated vices
4 x 65mm jaws
1 x 50mm jaws

5 x Pneumatic Vices

Skylarc Ref S159912

Small air operated vices
65mm jaws
One side mounted stand

2 Vices and T Slot Stand

Skylarc Ref R159911

Record mill vice
100mm jaws
65mm mill vice
160mm x 210mm T slot table

Mill Vice

Skylarc Ref P159909

120mm jaws with 80mm brass jaws installed
Mounted in 2 axis stand (no handle)

Workshop Trolley

Skylarc Ref L159905

Steel frame
Timber top and shelf

Bishamon Pallet Jack

Skylarc Ref D159897

Bishamon 2000kg pallet jack
One fork has been bent and repaired
Sticks at it's lowest level on that wheel

6x Assorted Dial Gauges, Faulty / Heavy Use Units

Skylarc Ref G160758

6x Assorted Dial Gauges, Faulty / Heavy Use Units.
Mitutoyo, Mecer, Oldak brands.
Heavy dial face fading, stiff or non- moving shank, or broken shank, see photos.

Assorted Lifting Equipment

Skylarc Ref Y160880

Chain block, missing hook, doesn't work
2 x small lifting chains
Both 1500kg
1.7 and 1.3 metre

Record Vice

Skylarc Ref S160874

Record No.6
150mm jaws

Large Milling Machine Angle Plate

Skylarc Ref R160873

Milling angle plate

Assorted Lathe Tools

Skylarc Ref P160871

13 lathe tools

2 x Rockwell Cordless Impact Drivers

Skylarc Ref H160863

Rockwell Shop Series
18v cordless impact driver
2 x batteries
Charger
Case
1/2"
One works the other doesn't
Both batteries work

Cabinet of Industrial Supplies

Skylarc Ref C160598

Steel two door cabinet
Contents include
Nuts, bolts, screws

3 x BT40 Tool Holders

Skylarc Ref D161041

3 x BT40 Tool Holders

3 x BT40 Tool Holders

Skylarc Ref C161040

3 x BT40 Tool Holders

Heavy Duty Steel Cabinet

Skylarc Ref S160588

Steel cabinet
Handles on side
Very heavy

Ingersol Rand Air Impact Driver

Skylarc Ref Q160586

Ingersol Rand A11 Impactool Model A
3/4" drive

Magnetic Transfer Block

Skylarc Ref H160577

280mm x 105mm x 20mm
Needs a cleanup, some corrosion on bottom

Eclipse Magnetic Chuck

Skylarc Ref G160576

Eclipse Non-Electric Magnetic Chuck
355mm x 150mm surface
Some surface corrosion but works fine

Tool Cutter Grinder Drill Relief Attachment

Skylarc Ref F160575

The Alston Tool & Gauge Company
Single phase
Variety of collets
Change gears

2x Partial Tap & Die Sets

Skylarc Ref K160710

2x Partial Tap & Die Sets.
485x320x48mm Steel blue case Metric tap and die set.
315x200x40mm plastic grey Metric tap a d die set.
Both sets are missing pieces, see photos.

10 Lathe Turning Tools

Skylarc Ref A160570

25mm shank lathe tools

10 Lathe Turning Tools

Skylarc Ref Z160569

25mm shank lathe tools

Large Lot of Lathe Turning Tools

Skylarc Ref Y160568

Assorted lathe tools
25mm shank lathe tools mainly
19 total
Surface rust on tops

Large Assortment of Drill Bits

Skylarc Ref B161013

Large Assortment of Drill Bits

4 Large Lathe Boring Bars

Skylarc Ref X160567

Sandvik Maxp S40V-PSKNR 12
Unknown brand 30mm shank
S25T-SCLR 09
HR136-17-0025

15 Morse Taper Drill Bits

Skylarc Ref W160566

Largest size 26.5mm
Smallest 12.25mm (measured)

16 Morse Taper Drill Bits

Skylarc Ref V160565

Largest size 18mm
Smallest 15mm

19 Morse Taper Drill Bits

Skylarc Ref U160564

Largest size 15/16"
Smallest 9/16"
Mainly imperial sizes

10 Morse Taper Drill Bits

Skylarc Ref T160563

Largest size 30mm
Smallest 29"
Metric and imperial sizes

10 Morse Taper Drill Bits

Skylarc Ref S160562

Largest size 1 3/32"
Smallest 22mm
Metric and imperial sizes

10 Morse Taper Drill Bits

Skylarc Ref R160561

Largest size 32mm
Smallest 15/16"
Metric and imperial sizes

10 Morse Taper Drill Bits

Skylarc Ref Q160560

Largest size 1 1/4"
Smallest 23.5mm
Metric and imperial sizes

10 Morse Taper Drill Bits

Skylarc Ref P160559

Largest size 36mm
Smallest 25mm
Metric and imperial sizes

Large Assortment of Lathe Inserts

Skylarc Ref Z161011

Assortment of Lathe Inserts.

10 Morse Taper Drill Bits

Skylarc Ref O160558

Largest size 1 15/32"
Smallest 16.5mm (measured)
Metric and imperial sizes

5 Large Morse Taper Drill Bits

Skylarc Ref N160557

Largest size 1 29/52"
Smallest 1 5/16"
Imperial sizes

5 Large Morse Taper Drill Bits

Skylarc Ref M160556

Largest size 50.5mm
Smallest 1 7/16"
Metric and imperial sizes

5 Large Morse Taper Drill Bits

Skylarc Ref L160555

Largest size 1 15/16"
Smallest 1 15/32"
Imperial sizes

4 Large Morse Taper Drill Bits

Skylarc Ref K160554

3 x 1 3/4"
42mm

4 Large Morse Taper Drill Bits

Skylarc Ref J160553

1 13/16"
45mm
50mm
2 1/8"

3 Very Large Morse Taper Drill Bits

Skylarc Ref I160552

54mm
65mm
70mm

AS Taylor Turret Lathe

Skylarc Ref F160549

Taylor Turret Lathe
180mm chuck
6 tool turret
Three phase
Includes cabinet of tooling located in rear room behind machine

Sturdy Workshop Trolley Cart

Skylarc Ref C160702

Sturdy Workshop Trolley Cart.
Angle steel frame with wood board surfaces.
Very dirty and well used but still very sturdy and rolls smoothly.

Sturdy Workshop Trolley Cart

Skylarc Ref O161000

Sturdy Workshop Trolley Cart.
Angle steel frame with MDF board surfaces.
Shows heavy usage but still sturdy.

Desoutter Air Grinder Type '04'

Skylarc Ref Y161400

Desoutter Air Grinder Type '04'
Made in England
Includes a 2 meter air hose, multiple attachments, 1 Collet and a Wooden Box.
Item operates as normal.

Workshop Mill Tool Holder Shelf Trolley Cart

Skylarc Ref J160995

Workshop Mill Tool Holder Shelf Trolley Cart.
Tool holder holes in top plywood are 45mm diameter.
Two lower shelves.
Rolls easily.

Heavy Duty Scrap Metal Bin Trolley

Skylarc Ref I160994

Heavy Duty Scrap Metal Bin Trolley.
Interior depth 445mm.
Rolls easily on large castors.

10 Shelf Cabinet

Skylarc Ref Y160542

10 shelf Cabinet with Contents, 1 shelf is missing

Milling Machine Angle Plate

Skylarc Ref X160541

Cast angle plate

Antique Wood Beam Lifting Apparatus

Skylarc Ref G160992

Antique Wood Beam Lifting Apparatus.
Unsure as to its specific purpose.
Grooves cut into top of wood beam at approx 50mm intervals.
Wood beam approx 1850x90x45mm.
Age unknown.
See photos for further design details.

Lot of Assorted Tooling

Skylarc Ref W160540

Various high speed milling tools
Drill bits
End mills
Taps
And more

Milling Machine Angle Plate

Skylarc Ref V160539

Cast angle plate

Large Lot of Drill Bits

Skylarc Ref U160538

Taper shank drills
Wide range of HSS drills
Approx 40

Sturdy Workshop Shelf Trolley Cart

Skylarc Ref A160986

Sturdy Workshop Shelf Trolley Cart.
Angle steel frame with MDF shelves.
Well used but rolls good and sturdy.

T Slot Table

Skylarc Ref Q161392

T Slot Table is 50mm Deep with 30mm deep slots that run the length and width of the table. The top gap of the slot is 15mm and the bottom is 30mm. total top width and length is 265mm x 265mm with extensions on either side of 50mm with a bolt gap of 20mm and a depth of 20mm

Blue Gizmo Hight Temperature Infrared Thermometer

Skylarc Ref X160983

Blue Gizmo Hight Temperature Infrared Thermometer.
Model No. BG 47/48
Includes case snd instruction manual.
9V battery depleted so unable to test
Previously used in a foundry room so shows typical foundry grime and wear.

Vintage Hoffman Precision Roller Gauge Set, Imperial Sizes

Skylarc Ref T160979

Vintage Hoffman Precision Roller Gauge Set.
Made in Chelmsford, England, by Hoffman Manufacturing Co. Ltd.
Age of set unknown.
Hardwood case with felt inner lining approx 220x110x50mm.
Complete set with one extra piece.
Sizes from 3/16" to 1 1¹¼".
Overall very good condition for a classic vintage set.

Scientific Microscope

Skylarc Ref N160973

Scientific Microscope.
Unknown brand and model.
3x optics, see photos for sizes.
Single eye optic.
Measures approx 180x130x335mm.
Built-in light is operating. 2x extra LED lights are attached.

Vintage Inch to Millimetre to Inch Conversion Calculator

Skylarc Ref L160971

Vintage Inch to Millimetre to Inch Conversion Calculator.
Back before we all asked Google how to convert metric to Imperail and back, there was Tools like this!
Made in England by M.H. Measures & Co., Huddersfield.
The 276mm diameter disk converts from 0mm (0 inch) to 254mm (10").
Includes case.
Disk calculator generally in excellent condition. Case exterior shows much grime and wear from Workshop storage.

Bomac 500kg Beam Trolley

Skylarc Ref K160970

Bomac 500kg Beam Trolley.
260mm length.
Inner width at wheels approx 135mm.

2x Kennametal BT40 Type Tool Holders

Skylarc Ref G160966

2x Kennametal BT40 Type Tool Holders.
Includes:
- BT40-DA18B-100M
- BT40-EM32-110M with 75mm diameter boring attachment.

Workshop Mobile Shelf Trolley

Skylarc Ref C160962

Workshop Mobile Shelf Trolley.
25x25mm box steel frame with 25mm thick MDF shelves.
Items seen on shelves not included.
Shelf mounted on 130mm diameter castors.

2x Lead Sheets

Skylarc Ref R160951

2x Lead Sheets.
Each folded sheet is approx 900x850mm. Thickness is around 2-3mm.

Workshop Mobile Shelf Trolley

Skylarc Ref Q160950

Workshop Mobile Shelf Trolley.
Angle steel frame with wood board lower and upper surfaces.
Top surface also has a thin sheet of plywood over wood board.
Well used but sturdy Trolley.

Workshop Mobile Shelf Trolley

Skylarc Ref L160945

Workshop Mobile Shelf Trolley.
Angle steel frame 700x465mm with wood board lower shelf and a larger 835x725mm MDF board top shelf.
MDF board shows heavy wear. Trolley frame solid and rolls ok.